Supermicro 5018D2-AR12L Скачать руководство пользователя страница 93

Страница: 93 / 124

Chapter 7: BIOS

7-15

XHCI Hand-Off

This is a work-around solution for operating systems that do not support XHCI (Ex-

tensible Host Controller Interface) hand-off. The XHCI ownership change should be

claimed by the XHCI driver. The settings are

Enabled

and Disabled.

EHCI Hand-Off

This item is for the Operating Systems that do not support Enhanced Host Controller

Interface (EHCI) hand-off. When this item is enabled, EHCI ownership change will

be claimed by the EHCI driver. The settings are Enabled and

Disabled

USB 3.0 Support

Select Enabled for USB 3.0 support. The options are Smart Auto,

Auto

, Enabled,

Disabled.

EHCI1

Select Enabled to enable EHCI (Enhanced Host Controller Interface) support on

USB 2.0 connector #1 (at least one USB 2.0 connector should be enabled for EHCI

support). The options are Disabled and

Enabled

EHCI2

Select Enabled to enable EHCI (Enhanced Host Controller Interface) support on

USB 2.0 connector #2 (at least one USB 2.0 connector should be enabled for EHCI

support). The options are Disabled and

Enabled

XHCI Pre-Boot Driver

Select Enabled to enable XHCI (Extensible Host Controller Interface) support on a

pre-boot drive specified by the user. The options are

Enabled

and Disabled.



SATA Configuration

When this submenu is selected, the AMI BIOS automatically detects the presence

of the SATA devices that are supported by the Intel PCH chip and displays the

following items:

SATA Controller

This item enables or disables the onboard SATA controller supported by the Intel

PCH chip. The options are

Enabled

and Disabled.

Configure SATA as

Select IDE to configure a SATA drive specified by the user as an IDE drive. Select
AHCI to configure a SATA drive specified by the user as an AHCI drive. Select
RAID to configure a SATA drive specified by the user as a RAID drive. The options

are IDE,

AHCI

, and RAID.

Содержание 5018D2-AR12L





























































































































Результаты поиска

Содержание 5018D2-AR12L

Отзывы:

Похожие инструкции для 5018D2-AR12L

Бренды по названию

Популярные бренды

Supermicro 5018D2-AR12L, Руководство пользователя

Результаты поиска

Содержание 5018D2-AR12L

Отзывы:

Похожие инструкции для 5018D2-AR12L

Бренды по названию

Популярные бренды