Supermicro 5018D2-AR12L Скачать руководство пользователя страница 84

Страница: 84 / 124

7-6

UPER

TORAGE

YSTEM 5018D2-AR12L/D4-AR12L/D8-AR12L User's Manual



CPU Configuration

The following CPU information will be displayed:

•

Processor ID

•

Processor Frequency

•

Processor Max Ratio

•

Processor Min Ratio

•

Microcode Revision

•

L1 Cache RAM

•

L2 Cache RAM

•

L3 Cache Ram

•

CPU Version

Clock Spread Spectrum

If this feature is set to Enabled, the BIOS utility will monitor the level of Electro-

magnetic Interference caused by the components and will attempt to reduce the

interference whenever needed. The options are

Disable

and Enable.

Hyper-Threading (ALL)

Select Enable to use Intel Hyper-Threading Technology to enhance CPU perfor-

mance. The options are Disable and

Enable

Cores Enabled

Set a numeric value to enable the number of cores. (Please refer to Intel's website

for more information.) Enter

to enable all cores.

Monitor/Mwait

Select Enabled to enable the Monitor/MWait instructions. The Monitor instruction

monitors a region of memory for writes, and MWait instructions instruct the CPU to

stop until the monitored region begins to write. The options are Disable and

Enable

Содержание 5018D2-AR12L





























































































































Результаты поиска

Содержание 5018D2-AR12L

Отзывы:

Похожие инструкции для 5018D2-AR12L

Бренды по названию

Популярные бренды

Supermicro 5018D2-AR12L, Руководство пользователя

Результаты поиска

Содержание 5018D2-AR12L

Отзывы:

Похожие инструкции для 5018D2-AR12L

Бренды по названию

Популярные бренды