SuperMax 19-38 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 32

SuperMax 19-38 Скачать руководство пользователя страница 22

22

MAINTENANCE

Monthly Maintenance Checklist

For best results perform the following procedures

on a monthly basis:

•

Lubricate conveyor bushings and check for

wear.

•

Lubricate with a dry lubricant spray all of

the moving parts, such as threaded rods

and washers.

•

Clean dust from conveyor belt.

•

Check all set screws for tightness.

•

Clean drum and abrasives if necessary.

Cleaning the Machine

The sander may need to be cleaned more frequent-

ly depending upon frequency of use. The drum

and the conveyor belt need to be clean. Allowing

excess build-up of dust and debris can adversely

affect performance and increase the likelihood of

slippage on the conveyor belt. Sweep the conveyor

belt clean after all operations. When cleaning dust

from the drum leave the dust collection system on.

Replacing Conveyor Belts

To replace the conveyor belt, the conveyor assem-

bly must be removed from the machine.
1. Raise the drum carriage to its highest position

using the height adjustment handle.

2. Turn off power source to machine.
3. Unplug main drive motor and inverter from re-

ceptacle (in gear motor assembly).

4. Loosen the conveyor take-up screws to relieve

belt tension and slide the driven roller fully in-

ward.

5. Remove the two bolts (inboard side) that attach

the conveyor assembly to the base.

6. Remove the two nuts and washers (outboard

side).

7.   Lift the conveyor and remove it from the sander.
8.   Stand conveyor on motor side.
9.   Avoid tearing the belt on any edges underneath

the conveyor bed during removal.

Reverse the procedure for re-installation and re-in-

stall the conveyor bed to sander.

«
...
20
21
22
23
24
...
»

Содержание 19-38

































Отзывы:

Нет отзывов