background image

 

- 2 - 

RDO1 C 

IMPORTANT SAFETY RECOMMENDATIONS 

 

FAILURE TO COMPLY WITH THE FOLLOWING SAFETY RECOMMENDATIONS MAY RESULT IN 

 

SERIOUS PERSONAL INJURY AND/OR PROPERTY DAMAGE

 

1.

 

For 

ADDITIONAL SAFETY

 we 

STRONGLY

 recommend the fitment of Photo Electric Safety Beams. 

In most countries the fitment of Photo Electric Safety Beams is mandatory on all garage doors fitted with 

Automatic Openers. recommends that Photo Electric Safety Beams

 

be installed with the Automatic Opener 

ensuring additional safety and peace of mind. 

2.

 

DO NOT

 operate the Garage Door Opener unless the Garage Door is in full view and free from objects 

such as cars, children or adults. 

3.

 

DO  NOT

  operate  the  Garage  Door  Opener  when  children/persons  are  near  the  door.  Children  must  be 

supervised at all times when near the garage door and when the Door Opener is in use. 

4.

 

DO NOT

 allow children to operate the Garage Door Opener. 

5.

 

Make sure that the 

SAFETY OBSTRUCTION FORCE

 is working correctly, and is 

TESTED

 and set as 

per  the  Installation  Instructions  Manual.  This  test  must  be  carried  out  6  monthly  and  the  necessary 

adjustments made if required. 

6.

 

DO  NOT

  disengage  the  Door  Opener  to  manual  operation  with  children/persons  or  and  other  objects 

including motor vehicles under the doorway. 

7.

 

Install the wall switch or wall mounted transmitter in a location/position where the garage door is visible 

and 

OUT OF REACH OFF CHILDREN

8.

 

The  Garage  door  must  be 

WELL  BALANCED

.  Sticking,  binding  or  out  of  balance  doors  must  be 

repaired by qualified garage door installer prior to Opener installation. 

9.

 

DO NOT

 attempt to repair door yourself as hardware is under extreme tension and can cause 

SERIOUS 

PERSONAL INJURY

 and/or property damage. 

10.

 

REMOVE OR DISSABLE

 all garage doors locks and mechanisms prior to installation of the Opener. 

11.

 

Connect  the  Garage  Door  opener  to  a  properly

  EARTHED

  general  purpose  220V  outlet  installed  by  a 

qualified electrical contractor. 

12.

 

ALWAYS  DISCONNECT  THE  POWER  CORD

  from  main  power  before  making  any  repairs  or 

removing covers. Only 

EXPERIENCED

 service personnel can remove covers from the Opener. 

13.

 

Keep hands and loose clothing CLEAR of the door and Door Opener at all times. 

14.

 

When  using  auto  close  mode  a 

PHOTOELECTRIC  BEAM

  must  be  fitted  and  tested  for  correct 

operation  at  regular  intervals. 

EXTREME  CAUTION

  is  recommended  when  using  auto  close  mode. 

ALL SAFETY RULES

 must be observed. 

15.

 

In order for the Garage Door Opener to 

SENSE

 an object obstruction, some

 FORCE

 must be exerted on 

the object/person and the door. As a result the object/person/door may suffer 

DAMAGE OR INJURY.

 

16.

 

Make sure that the door is fully open before driving into or out of the garage. 

17.

 

Make sure the door is fully closed before leaving the driveway. 

 

 

Содержание RDO1 C
















Отзывы: