Superior Fireplaces DRC3500 Скачать руководство пользователя страница 54

Страница: 54 / 70

Operation

900298-00, 10/2014

Innovative Hearth Products
Superior

DRT/DRC3500 Series Direct-Vent Gas Fireplaces

Installing the Backup Batteries

With a battery backup, electronic fireplaces can automatically switch to battery power. In the event of a power outage, this

allows ON/OFF operation (without blower functionality). Install new batteries before every burn season.

Open the Wall Switch (

Page 40

), and locate the battery holder.

Install four (4) AA batteries in the battery holder.

Close the battery holder.

Continuous Pilot Ignition Switch

Fireplaces with an electronic gas valve have a continuous pilot ignition (CPI) controlled by the remote
This switch allows the pilot to be switched from intermittent mode to continuous mode:

•

Intermittent Mode—The pilot is extinguished when the fireplace is OFF.

•

Continuous Mode—The pilot stays ON when the fireplace is OFF.

In periods of extreme cold, condensation may form on the glass door when the fireplace is OFF and the pilot is in

intermittent mode. Also, with the pilot in intermittent mode, the fireplace may

cycle startup

(i.e., the pilot and burner ignite,

but the burner extinguishes and reignites several times until the flue reaches the temperature for proper drafting).

•

To save energy—switch to intermittent mode.

•

For a standing pilot that will help prevent glass door condensation and cycle startup—switch to continuous mode.

NOTE:

Continuous mode is indicated by a pilot that comes ON and remains lit when the fireplace is OFF.

Traditional Only: Installing the Firebox Liners

Remove the three (3) optional firebox liner panels from the packing materials if purchased.

Carefully position the rear panel, upper edge first, in the firebox against the rear wall.

While holding the rear panel, carefully position the left side panel in the firebox.

Carefully position the right side panel in the firebox.

NOTE:

Do not force the panels. Excessive force may cause breakage. If the panels are correctly positioned, they will

fit snugly in place.

NOTE:

Contemporary Only: Installing the Glass Media

Install the glass media in the recessed area between the front and rear floors.

NOTE:

35” fireplaces require less than a full bag of glass media. 40” fireplaces require an entire bag of media.

Spread the glass media in a thin layer, evenly over the burner and pilot.

NOTE:

Do NOT mound the media.

Содержание DRC3500







































































Результаты поиска

Содержание DRC3500

Отзывы:

Похожие инструкции для DRC3500

Бренды по названию

Популярные бренды

Superior Fireplaces DRC3500, Инструкция по установке и эксплуатации

Результаты поиска

Содержание DRC3500

Отзывы:

Похожие инструкции для DRC3500

Бренды по названию

Популярные бренды