Superior Fireplaces DRC3500 Скачать руководство пользователя страница 44

Страница: 44 / 70

Installation

900298-00, 10/2014

Innovative Hearth Products
Superior

DRT/DRC3500 Series Direct-Vent Gas Fireplaces

20.

Install the Hood

NOTE:

All models must have a hood installed prior to operation.

Install the hood by sliding it into the slots on the lower edge of the cabinet top.

NOTE:

To install the non-combustible finish material flush with the top of the hood, the hood must be installed

before installing the finish material. If finish material is installed flush with the top edge of the hood, the hood cannot

be removed.

NOTE:

To install the hood after installing the non-combustible finish material over the black surface above the

fireplace opening, the bottom edge of the finish material must be 5/8” above the top edge of the hood to allow

clearance for installation and removal of the hood.

21.

Reinstall the Included Barrier

WARNING

Reinstall any barrier removed before operating the fireplace. The barrier is designed

to reduce the risk of burns from hot glass. Do not operate the fireplace without the

barrier installed.

NOTE:

All models must have a barrier installed prior to operation.

Open the control compartment door (

Page 53

Hold the barrier in front of the glass door and slide it up into the slots above the glass door and under the hood.

Slide the barrier bottom down into the slots below the glass door, securing it in place.

22.

Install the Finishing Materials

Complete finished interior wall.

NOTE:

To install the fireplace facing flush with the finished wall, position framework to accommodate the thickness

of the finished wall.

Figure 39: Combustible Wall Framing

Top Of

Appliance

3”

(76 mm)

This Area

Must Remain

Clear of

Combustible

Materials

1” Min.

(25 mm)

4” Clearance

Minimum

Hood

Standoff

Provides

Space From

Combustible

Materials

Stand Off

Must Be Bent

To Vertical

Position

Combustible

Finished Wall

Materials

NOTE:

See

Cold Climate Insulation on Page 10

and

Vent Termination Clearances on Page 13

23.

Attach the Safety-in-Operation Warning Labels

Attach the furnished safety instruction labels at all fireplace operation and control points (

Page 45

NOTE:

The installer MUST ensure these warnings are properly attached during installation. The warning labels are a

critical means of informing consumers of safe operation practices.

Содержание DRC3500







































































Результаты поиска

Содержание DRC3500

Отзывы:

Похожие инструкции для DRC3500

Бренды по названию

Популярные бренды

Superior Fireplaces DRC3500, Инструкция по установке и эксплуатации

Результаты поиска

Содержание DRC3500

Отзывы:

Похожие инструкции для DRC3500

Бренды по названию

Популярные бренды