Superior Fireplaces DRC3500 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 70

background image

Installation

900298-00, 10/2014

Innovative Hearth Products
Superior

TM

DRT/DRC3500 Series Direct-Vent Gas Fireplaces

20

4.

Determining Vent Setup in the Combination Venting Unit

Combination venting units are shipped with rear venting setup nearly ready for install. If this is the type of vent you require, remove
all insulation packing and flue plug block off from rear venting and proceed with fireplace installation.

If you require a top-vented unit, use the following steps to convert the fireplace before use.

5.

Installing Non-Combustible Front Fireboard Standoff

A non-combustible standoff board is provided with the fireplace to prevent overlap of drywall or other material of portions of the
fireplace that may be prone to the buildup of heat. It is supported by a middle bracket and two side brackets.

Step 1:

Remove the eight (8) screws

holding the top vent cover plate and

gasket.

Step 2

: Remove the round flue

cover from the top venting outlet.

Step 3

: Remove insulation from inside

flue pipe.

Step 4

: Make sure insulation disc is

still in the round cover. Remove the

flue plug from the top flue.

Step 5

: Bend tabs out on round flue cover. Secure the round flue cover (provided) to

the wrapper over the rear venting outlet. Use two (2) 3/4” long sheet metal screws

Separate and note metal side

(2) and center (1) brackets.

Step 1:

Remove two screws from the top and side of the unit. Bend the side bracket securing tab

over the edge of the unit and secure. Secure bracket to the top through the clearance screwhole.

Step 2:

Remove the three screws that align with the clearance

screwholes from the top of the unit. Secure the center bracket

to the top center of the fireplace

Step 3:

Top of front fireboard

standoff should be flush with

top standoffs (not shown).

Step 4:

Fireboard standoff

can be secured to the cap-

ture screwholes.

«
...
18
19
20
21
22
...
»

Содержание DRC3500







































































Отзывы:

Нет отзывов

Похожие инструкции для DRC3500

Бренд: L'Artistico Страницы: 48

Бренд: RAIS Страницы: 18

CROSSOVER CO10-101-M

Бренд: Magma Страницы: 18

Бренд: Valor Страницы: 60

Бренд: T&C Страницы: 16

Бренд: Fisher Страницы: 16

Бренд: Napoleon Страницы: 21

Бренд: Superior Fireplaces Страницы: 28

Бренд: Majestic Страницы: 36

Бренд: Kingsman Страницы: 59

Бренд: La Hacienda Страницы: 4

Бренд: glamour Страницы: 12

Бренд: Valor Страницы: 4

HeatFlo Kit HTFLO-LIN60

Бренд: IHP Страницы: 8

Бренд: Hargrove Страницы: 10

Бренд: Spatherm Страницы: 24

Бренд: Spartherm Страницы: 28

Бренд: Arada Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды