Superior Fireplaces DRC3500 Скачать руководство пользователя страница 37

Страница: 37 / 70

Installation

900298-00, 10/2014

Innovative Hearth Products
Superior

DRT/DRC3500 Series Direct-Vent Gas Fireplaces

Slide the outer flexible vent over the adaptor collar. Ensure the flexible vent completely engages the adaptor collar

1 3/4” from the end, and that it is free from damage or tears.

Slide the gear clamp down and tighten it fully to secure the flexible vent to the adaptor outer collar

approximately 3/4” from the end of the flexible vent.

Install three (3) screws 120° apart through the flexible vent and into the adaptor collar just below the gear

clamp to provide additional security to the connection.

Route the flexible vent.

NOTE:

Ensure that the flexible vent is properly routed to provide the required clearance. Do NOT allow the flexible vent

to bend in a radius tighter than 5” (127 mm) (

Figure 30

). Place the internal flexible vent spacers evenly and avoid

kinking the inner vent. Support horizontal sections of flexible vent with metal straps at 2 ft (0.61 m) intervals.

Install firestop/spacers at ceiling and wall penetrations.

•

SF4.5 VF firestop/spacer for ceilings

•

SF4.5 HF firestop/spacer for walls

NOTE:

See the appropriate sections and figures shown throughout the venting section for installation

requirements.

Attach the flexible vent to the termination.

NOTE:

Secure Flex

components can be purchased separately and attached to bulk lengths of Secure Flex flexible

vent cut to size at the job site. Attach the flexible vent to the Secure Flex terminations as it was attached to the

adaptor (

Figure 29

NOTE:

Attach Secure Flex vent to Secure Flex terminations only. Do NOT substitute Secure Vent

terminations

or Secure Vent adaptor for Secure Flex components. Secure Flex termination and adaptor collars are a

different circumference than Secure Vent collars. Secure Flex vent has an longer center tube to improve

ease-of-installation.

12.

Complete the Field Wiring

CAUTION

The ground supply lead must be connected to the wire attached to the green ground screw

located on the outlet box (see wiring diagrams). Failure to do so will result in a potential

safety hazard. The appliance must be electrically grounded in accordance with local codes

or, in the absence of local codes, the National Electrical Code, ANSI/NFPA 70—latest

edition (in Canada, the current CSA C22-1 Canadian Electrical Code).

CAUTION

Label all wires prior to disconnection when servicing controls. Wiring errors can cause

improper and dangerous operation.

ATTENTION

Au moment de l’entretien des commandes, étiquetez tous les fils avant de les débrancher.

Des erreurs de cáblage peuvent entraîner un fonctionnement inadéquat et dangereux.

Verify proper operation after servicing.

S’assurer que l’appareil fonctionne adéquatement une fois l’entretien terminé.

The gas valve is set in place and pre-wired at the factory for both millivolt and electronic models.

Содержание DRC3500







































































Результаты поиска

Содержание DRC3500

Отзывы:

Похожие инструкции для DRC3500

Бренды по названию

Популярные бренды

Superior Fireplaces DRC3500, Инструкция по установке и эксплуатации

Результаты поиска

Содержание DRC3500

Отзывы:

Похожие инструкции для DRC3500

Бренды по названию

Популярные бренды