Super PDSMi Скачать руководство пользователя

Страница: 17 / 100

Chapter 1: Introduction

1-11

Depressing the power button again will cause the whole system to wake-up. Dur-

ing the SoftOff state, the ATX power supply provides power to keep the required

circuitry in the system alive. In case the system malfunctions and you want to turn

off the power, just depress and hold the power button for 4 seconds. The power

will turn off and no power will be provided to the motherboard.

Wake Ring-On (WOR)

Wake-up events can be triggered by a device such as the external modem ringing

when the system is in the SoftOff state. Note that external modem ring-on can only

be used with an ATX 2.01 (or above) compliant power supply.

Wake-On-LAN (WOL)

Wake-On-LAN is deﬁ ned as the ability of a management application to remotely

power up a computer that is powered off. Remote PC setup, up-dates and asset

tracking can occur after hours and on weekends so that daily LAN trafﬁ c is kept to

a minimum and users are not interrupted. The motherboard has a 3-pin header

(WOL) to connect to the 3-pin header on a Network Interface Card (NIC) that has

WOL capability. Note that Wake-On-LAN can only be used with an ATX 2.01 (or

above) compliant power supply.

1-5 ACPI Features

ACPI stands for Advanced Conﬁ guration and Power Interface. The ACPI speciﬁ -

cation deﬁ nes a ﬂ exible and abstract hardware interface that provides a standard

way to integrate power management features throughout a PC system, including its

hardware, operating system and application software. This enables the system to

automatically turn on and off peripherals such as CD-ROMs, network cards, hard

disk drives and printers. This also includes consumer devices connected to the PC

such as VCRs, TVs, telephones and stereos.

In addition to enabling operating system-directed power management, ACPI

provides a generic system event mechanism for Plug and Play and an operating

system-independent interface for conﬁ guration control. ACPI leverages the Plug

and Play BIOS data structures while providing a processor architecture-indepen-

dent implementation that is compatible with both Windows and Linux Operating

Systems.

1-6 Power Supply

As with all computer products, a stable power source is necessary for proper and

reliable operation. It is even more important for processors that have high CPU

clock rates of 1 GHz and faster.

Содержание PDSMi





































































































Результаты поиска

Содержание PDSMi

Отзывы:

Похожие инструкции для PDSMi

Бренды по названию

Популярные бренды

Super PDSMi, Руководство пользователя

Результаты поиска

Содержание PDSMi

Отзывы:

Похожие инструкции для PDSMi

Бренды по названию

Популярные бренды