Super PDSMi Скачать руководство пользователя

Страница: 55 / 100

Chapter 4: BIOS

4-7

4-4 Advanced

Setup

Choose Advanced from the Phoenix BIOS Setup Utility main menu with the arrow

keys. You should see the following display. The items with a triangle beside them

have sub menus that can be accessed by highlighting the item and pressing <Enter>.

Options for PIR settings are displayed by highlighting the setting option using the

arrow keys and pressing <Enter>. All Advanced BIOS Setup options are described

in this section.

Boot Features

Access the submenu to make changes to the following settings.

Quick Boot Mode

If enabled, this feature will speed up the POST (Power On Self Test) routine by

skipping certain tests after the computer is turned on. The settings are

Enabled

and Disabled. If Disabled, the POST routine will run at normal speed.

Quiet Boot

Set to Enabled to display the Diagnostic Screen during POST. The settings are

Enabled

and Disabled.

ACPI Mode

Use the setting to determine if you want to employ ACPI (Advanced Conﬁ guration

and Power Interface) power management on your system. The options are

Yes

and No.

Содержание PDSMi





































































































Результаты поиска

Содержание PDSMi

Отзывы:

Похожие инструкции для PDSMi

Бренды по названию

Популярные бренды

Super PDSMi, Руководство пользователя

Результаты поиска

Содержание PDSMi

Отзывы:

Похожие инструкции для PDSMi

Бренды по названию

Популярные бренды