Super PDSMi Скачать руководство пользователя

Страница: 69 / 100

Chapter 4: BIOS

4-21

4-7 Exit

Choose Exit from the Phoenix BIOS Setup Utility main menu with the arrow keys.

You should see the following display. All Exit BIOS settings are described in this

section.

Exit Saving Changes

Highlight this item and hit <Enter> to save any changes you made and to exit the

BIOS Setup utility.

Exit Discarding Changes

Highlight this item and hit <Enter> to exit the BIOS Setup utility without saving any

changes you may have made.

Load Setup Defaults

Highlight this item and hit <Enter> to load the default settings for all items in the

BIOS Setup. These are the safest settings to use.

Discard Changes

Highlight this item and hit <Enter> to discard (cancel) any changes you made.

You will remain in the Setup utility.

Save Changes

Highlight this item and hit <Enter> to save any changes you made. You will remain

in the Setup utility.

Содержание PDSMi





































































































Результаты поиска

Содержание PDSMi

Отзывы:

Похожие инструкции для PDSMi

Бренды по названию

Популярные бренды

Super PDSMi, Руководство пользователя

Результаты поиска

Содержание PDSMi

Отзывы:

Похожие инструкции для PDSMi

Бренды по названию

Популярные бренды