Super PDSMi Скачать руководство пользователя

Страница: 83 / 100

Appendix C: Software Installation

C-1

Appendix C

Software Installation

After all the hardware has been installed, you must ﬁ rst conﬁ gure Intel's ICH7R

SATA RAID* before you install the Windows Operating System and other software

drivers.

Important Notes to the User:

*Note 1: If you do not wish to conﬁ gure onboard SATA RAID functions, please go

directly to Section C-4 for Operating System & Other Software Installation.

*Note 2: This chapter describes RAID Conﬁ guration Instructions for the Intel ICH

RAID Controller designed for the Windows OS. If you choose to use the Linux

OS, please enable Adaptec's RAID Controller in the BIOS and refer to the ﬁ le:

"E7230 Note.txt" in the folder: "Intel E7230" saved in the CD that came with your

motherboard for Adaptec RAID Conﬁ guration Instructions.

C-1 Introduction to Serial ATA and Parallel ATA

To conﬁ gure the SATA RAID functions, you must ﬁ rst use the Intel ICH7R SATA

RAID Utility program to conﬁ gure the RAID Level that you desire before installing

the Windows XP/2000/2003 operating system and other software drivers. (The

necessary drivers are all included on the Supermicro CD that came packaged with

your motherboard.) Note that the current version of the ICH7R SATA RAID Utility

can only support Windows XP/2000/2003 Operating Systems.

Serial ATA (SATA)

Serial ATA (SATA) is a physical storage interface that uses a single cable with a

minimum of four wires to create a point-to-point connection between devices. It is

a serial link, which supports transfer rates up to 3Gbps. Because the serial cables

used in SATA are thinner than the traditional cables used in Parallel ATA (PATA),

SATA systems have better airﬂ ow and can be installed in smaller chassis than

Parallel ATA. In addition, the cables used in PATA are limited to a length of 40cm,

while Serial ATA cables can be up to one meter in length. Overall, SATA provides

better functionality than PATA.

Introduction to Intel ICH7R Serial RAID

Located in the South Bridge of the E7230 Mukilteo chipset, the I/O Controller Hub

(ICH7R) provides the I/O subsystem with access to the rest of the system. It sup-

ports a 2-channel UltraATA/100 Bus Master IDE controller (PATA) and four Serial

ATA (SATA) ports. The ICH7R supports the following PATA and SATA device con-

ﬁ gurations: Legacy mode and Native mode.

Содержание PDSMi





































































































Результаты поиска

Содержание PDSMi

Отзывы:

Похожие инструкции для PDSMi

Бренды по названию

Популярные бренды

Super PDSMi, Руководство пользователя

Результаты поиска

Содержание PDSMi

Отзывы:

Похожие инструкции для PDSMi

Бренды по названию

Популярные бренды