Super PDSMi Скачать руководство пользователя

Страница: 54 / 100

4-6

PDSMi User's Manual

CHS Format

The following items will be displayed by the BIOS:

TYPE:

This item displays the type of CPU.

Cylinders:

This item indicates the status of Cylinders.

Headers:

This item indicates the number of headers.

Sectors:

This item displays the number of sectors.

Maximum Capacity:

This item displays the maximum storage capacity of

the system.

LBA Format

The following items will be displayed by the BIOS:

Total Sectors:

This item displays the number of total sectors available in

the LBA Format.

Maximum Capacity:

This item displays the maximum capacity in the LBA

Format.

Multi-Sector Transfer

This item allows the user to specify the number of sectors per block to be
used in multi-sector transfer. The options are

Disabled

, 4 Sectors, 8 Sectors,

and 16 Sectors.

LBA Mode Control

This item determines if the BIOS will access the Primary IDE Master Device via

the LBA mode. The options are Enabled and

Disabled

32 Bit I/O

This feature allows the user to enable or disable the function of 32-bit data

transfer. The options are Enabled and

Disabled

Transfer Mode

This feature allows the user to select the transfer mode. The options are

Standard

, Fast PIO1, Fast PIO2, Fast PIO3, Fast PIO4, FPIO3/DMA1, and

FPIO4/DMA2.

Ultra DMA Mode

This feature allows the user to select the Ultra DMA Mode. The options are

Disabled

, Mode 0, Mode 1, Mode 2, Mode 3, Mode 4, and Mode 5.

System Memory

This display informs you how much system memory is detected in the system.

Extended Memory

This display informs you how much extended memory is detected in the system.

Содержание PDSMi





































































































Результаты поиска

Содержание PDSMi

Отзывы:

Похожие инструкции для PDSMi

Бренды по названию

Популярные бренды

Super PDSMi, Руководство пользователя

Результаты поиска

Содержание PDSMi

Отзывы:

Похожие инструкции для PDSMi

Бренды по названию

Популярные бренды