Suntex PC-300A Series Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 36

Suntex PC-300A Series Скачать руководство пользователя страница 20

3.5 Connection of transmitter and accessorial transmitter PH-300T

A.

Connect the GLASS point of transmitter PH-300T’s terminal to the electrode coaxial inner.

(

Note:

Remove the black conductive rubber); connect the REF point of transmitter PH-300T’s

terminal to the electrode coaxial shield.

B.

Regarding two-wire distributing system and three-wire distributing system please refer to ch3.6.

C.

Sign “PT-1000” on transmitter PH-300T’s terminal is the connector for automatic temperature

compensation probe, PT-1000, or applies a fixed temperature compensation resistance.

D.

The V+ and V- of transmitter PH-300T’s terminal respectively connect to DC12V+ and – of the

transmitter.

E.

The S+ and S- on transmitter PH-300T’s terminal respectively connect to GLASS and REF of

the transmitter.

F.

The I+ and I- on transmitter PH-300T’s terminal are output (4-20mA), which can connect to

devices that receive current signals.

Note:

1. Do not share the same power supply with more transmitters at a time under 2-wire
distributing system.

2. As the current output signal of transmitter is not insulated, it is unavailable to connect
with PC or PLC; or it would do damage on electrodes.)

Refer to the following table for proper fixed temperature compensation resistance
Temperature

0

°

C

5

°

C

10

°

C

15

°

C

20

°

C

R value

1000Ω

1019.25Ω

1038.5Ω

1057.75Ω

1077Ω

Temperature

25

°

C

30

°

C

35

°

C

40

°

C

45

°

C

R value

1096.25Ω

1115.5Ω

1134.75Ω

1154Ω

1173.25Ω

Temperature

50

°

C

55

°

C

60

°

C

65

°

C

70

°

C

R value

1192.5Ω

1211.75Ω

1231Ω

1250.25Ω

1269.5Ω

Temperature

75

°

C

80

°

C

85

°

C

90

°

C

100

°

C

R value

1288.75Ω

1308Ω

1327.25Ω

1346.5Ω

1385Ω

17

«
...
18
19
20
21
22
...
»

Содержание PC-300A Series





































Отзывы:

Нет отзывов