Sungrow SH5K Скачать руководство пользователя | Manualshive

Страница: 53 / 60

background image

Quick User Manual

5 Troubleshooting

41

Code

Specification

Troubleshooting

installed in sunlight or the ambient
temperature of the enclosure

exceeds 45

℃

.

3. Restart the system.

906

Transformer direction
recognition error.

1. The inverter can normally be
connected to the grid but
charge/discharge has stopped.
2. Wait a moment for system
recovery or restart the system.

910

FRAM2 warning

Restart the inverter.

For Battery Side

For the battery faults, please consult the battery manufacturer for a solution.

Code

Specification

Troubleshooting

703

Battery average
under-voltage fault.

1. The inverter can normally be
connected to the grid but
charge/discharge has stopped.
2. Wait a moment for system recovery or
restart the system.

707

Battery over-temperature
fault.

1. The inverter can normally be
connected to the grid but
charge/discharge has stopped.
2. Check the ambient temperature of the
battery location.
3. Wait a moment for system recovery or
restart the system.

708

Battery under-temperature
fault.

711

Instantaneous battery
over-voltage.

1. The inverter can normally be
connected to the grid but
charge/discharge has stopped.
2. Wait a moment for system recovery or
restart the system.

712

Battery average
over-voltage fault.

714

Abnormal communication
between battery and the
hybrid inverter.

1. The inverter can normally be
connected to the grid but
charge/discharge has stopped.
2. Check the battery type and
communication connection.
3. Wait a moment for system recovery or
restart the system.

715

Battery hardware
over-voltage fault.

1. The inverter can normally be
connected to the grid but
charge/discharge has stopped.
2. Wait a moment for system recovery or
restart the system.

732

Battery

over-voltage 1. The inverter can normally be

«
...
51
52
53
54
55
...
»

Содержание SH5K





























































Отзывы:

Нет отзывов

Похожие инструкции для SH5K

Бренд: Linear Technology Страницы: 22

iPort PT1000-CL

Бренд: Pleora Technologies Страницы: 29

Automotive Ethernet Converter

Бренд: X2E Страницы: 22

Бренд: Samlex Europe Страницы: 33

Бренд: Jaden Страницы: 173

Бренд: nedis Страницы: 48

BNI IOL-712-000-K023

Бренд: Balluff Страницы: 12

Бренд: Vacon Страницы: 44

Бренд: Autopilot Страницы: 13

Бренд: Lambda Страницы: 47

PowerClean Salt Econ

Бренд: CMP Страницы: 24

ControlMaster Edge

Бренд: R&M Страницы: 2

Бренд: GoMax Electronics Страницы: 12

Бренд: Optelecom-nkf Страницы: 4

Бренд: Cross Technologies Страницы: 18

Бренд: Motrona Страницы: 28

Бренд: Power Tech-On Страницы: 27

Бренд: Tripp Lite Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды