background image

16 

Clostridium difficile

 (C. diff) Prevention: 

Clorox Germicidal Wipes (Clorox Professional Products Company), EPA Reg. #67619-12 

These  pre-moistened  wipes  meet  the  CDC’s  recommendations  for 

Clostridium  difficile

  (C.diff) 

bacteria, after the manufacturer’s recommended “wet contact time”. 

1. Perform  hand  hygiene  using  soap  and  warm  water,  or  hand  sanitizer,  and  then  put  on

disposable gloves and eye protection.

2. Use  wipes  to  wipe  the  top  and  front  of  head/footboards,  hand  controls  and  cords,  side

rails and mattress top cover, making sure to wipe between the mattress and side rails.

3. Change  wipes  often  to  ensure  that  surfaces  remain  wet  with  disinfectant  for  the

manufacturer’s required contact time.  Used wipes are to be discarded in the trash.

4. Remove disposable gloves and discard in the trash; perform hand hygiene using soap and

warm water, or hand sanitizer, and then remove eye protection.

To reduce the discoloration of fabrics and degradation of the sleep surface lining, surfaces must 
be thoroughly rinsed with clean, fresh water to remove chemical residues immediately after the 
manufacturer’s  recommended  “wet  contact  time”  has  been  reached.    The  use  of  bleach-based 
solutions must be avoided whenever possible. 

Mattress Top Cover: 

Personal  Protective  Equipment  should  always  be  used  as  directed  by  the  disinfectant’s    Safety 
Data Sheet. 

1. Prepare the disinfectant according to the manufacturer’s recommendations.
2. Prepare a separate bucket of warm, fresh water to be used for rinsing the equipment after

cleaning/disinfecting procedures are completed as instructed.

3. All  surfaces  of  the  mattress  are  to  be  wiped  using  a  coarse  cloth  dampened  with  the

disinfectant,  prepared  as  directed  by  the  manufacturer’s  recommendations,  to  remove
organic material and visible soil.

4. Allow the mattress shell to remain wet with disinfectant solution for the manufacturer’s

recommended contact time.

5. Stains  on  the  mattress  top  cover  may  be  treated  using  an  approved  stain  remover,

according to the manufacturer’s recommendations.

6. Rinse  all  surfaces  of  the  mattress  with  fresh  water  and  clean  cloth  to  remove  chemical

and organic residue.

Laundry Instructions 

If  additional  cleaning  is  necessary,  top  covers  may  be  removed  and  laundered  using  standard 
hospital disinfectant/detergent.  

DO NOT use temperatures in excess of 120

F (49

C).

 

1. Set washing machine to Regular Cycle.
2. Pre-soak  with  disinfectant/detergent  in  cold  water  for  10  minutes.    DO  NOT  USE

HARSH SOLVENTS OR CLEANERS.

3. Main wash cycle: 15 minutes (time dependent on soil level).
4. Rinse cycle: 5 minutes, minimum.
5. Spin/Drain cycle: 5 minutes, minimum.

After washing, the mattress top cover is to be air dried or dried in a dryer at very low or no heat 
to protect it from heat related damage. 

Содержание Static Sapphire Pulse




































Отзывы: