manualshive.com logo in svg

Sun Microsystems SPARCcenter 2000, Руководство по установке

Поделиться
Скачать
Sun Microsystems SPARCcenter 2000 Скачать руководство пользователя страница 43

4-1

Powering the System On and Off

4

Use the instructions in this chapter to power on and off the system.

Note – The use of an ASCII terminal is recommended for installation. See
Section 3.5, “Connecting an ASCII Terminal” for terminal settings and
connections.

4.1 Powering On the System

Caution – For Solaris 2.X users: before powering on the system for the first
time, read Section 3.3, “Precautions for JumpStart Automatic Installation.”

To power on the SPARCcenter 2000 system:

1. Begin with a safety inspection of the system:

a. Turn the system key switch to

(the standby position).

See Figure 4-1.

Note – The standby position ( ) does not turn off any AC-powered drive trays
in the lower part of the system cabinet. The key switch controls only the DC
power supply and DC-powered devices in the main cabinet.

b. Turn the AC distribution unit power switch to Off.

The AC distribution unit is at the rear of the cabinet. See Figure 4-2.

!

Содержание SPARCcenter 2000



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды