manualshive.com logo in svg

Sun Microsystems SPARCcenter 2000, Руководство по установке

Поделиться
Скачать
Sun Microsystems SPARCcenter 2000 Скачать руководство пользователя страница 40

3-6

SPARCcenter™ 2000/2000E Installation Manual—June 1996

3

Note – If JumpStart automatic installation begins (unintentionally), interrupt
by pressing L1-A (Stop-A), and perform a manual installation when ready.

3.4 Connecting the System to the Network

1. Connect the network cable to a twisted-pair-to-transceiver interface box.

2. Connect the interface box via an appropriate cable to a network

transceiver.
Figure 1-6 on page 1-12 shows a typical arrangement for connecting the
system to an Ethernet network.

3.5 Connecting an ASCII Terminal

An ASCII terminal must be attached to the server for viewing diagnostic
messages. A terminal is not required for normal server operations, so it may be
necessary to find a terminal to connect to the server.

To connect an ASCII terminal:

1. Plug the terminal cable to port A on the system board in card cage slot 0.

See Figure 3-6. The system board in card cage slot 0 is normally the system
master in a new system.

Note – If the terminal does not display messages when the system is booted,
the terminal may be connected to the wrong system board. If this occurs, refer
to the SPARCcenter 2000 Service Manual for help in locating the system master.

Содержание SPARCcenter 2000



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды