manualshive.com logo in svg

Sun Microsystems SPARCcenter 2000, Руководство по установке

Поделиться
Скачать
Sun Microsystems SPARCcenter 2000 Скачать руководство пользователя страница 33

Unpacking the System

2-5

2

Figure 2-3

Rear Screen, Levelling Wrench, Kick Panel, and Levelling Pad

5. Slide the stabilizer bar into the cabinet.

Warning – Always extend the stabilizer bar before pulling the disk drive trays
out for servicing.

6. Adjust the four levelling pads on the cabinet frame. The four pads should

press against the floor so that the cabinet does not move.
To adjust levelling pads on the cabinet rear, you may have to remove the
kick panel. Two captive screws attach the panel to the cabinet (Figure 2-3).

This completes the first part of the system installation. If you are unable to
continue the installation at this time, close the cabinet:

1. Secure the levelling wrench inside the cabinet.

2. Replace the kick panel if the panel was removed.

3. Attach the rear screen.

Rear screen

Levelling wrench (in cabinet)

Kick panel

Levelling pad (1 of 6)

!

Содержание SPARCcenter 2000



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды