Summa S 75 Скачать руководство пользователя | Manualshive

Страница: 29 / 103

background image

S CLASS™ cutter

User’s Manual

Setup

1-19

1.5.4

Media load procedure

CAUTION:

Do not place any objects in front of, or behind, the cutter that could interfere

with cutter operation. Make sure the media is free to move forward and back. Keep
hands, hair, clothing and jewelry away from moving parts.

While the cutter is on, it will automatically start executing a minimal loading procedure
as soon as the pinch rollers are lowered. The load procedure will also start when the
cutter is switched on while media is already in the machine and the pinch rollers are in
the “down” position (this is not recommended). Always keep the pinch rollers in the up
position while the cutter is not being used.

The minimal loading procedure consists of:

A media width measurement.

Media is unwound over a length equal to the width measured between the

outer two pinch rollers.

A simultaneous 45° axial move of the drive drum (sleeves) and cutting head.

After that, the cutter is ready to receive files from the computer.
When receiving a job from the computer, the cutter will automatically pull the required
media from the roll. It does this in steps and the length of the vinyl used is equal to a
number of times the measured width of the media.

IMPORTANT:

Tracking of longer signs is only guaranteed when the full load procedure

is performed!

Full media load procedure:

WARNING

Each keystroke can initiate an internal test or movement of head or media.
Keep fingers and other body parts away from the cutting area.
There are hazardous moving parts.

«
...
27
28
29
30
31
...
»

Содержание S 75








































































































Отзывы:

Нет отзывов

Похожие инструкции для S 75

Бренд: RedMax Страницы: 23

Бренд: EUROM Страницы: 28

Бренд: Tanaka Страницы: 8

Бренд: Baumr Страницы: 52

Бренд: Eastwood Страницы: 12

AT-3623 AT-3630

Бренд: Dolmar Страницы: 116

Бренд: Bake Max Страницы: 10

Бренд: Ilco Orion Страницы: 24

Бренд: Rittal Страницы: 20

Precision Office A3+

Бренд: LEITZ Страницы: 30

Бренд: Virutex Страницы: 8

Бренд: Fac Страницы: 36

Бренд: IBEA Страницы: 80

Бренд: Garde Страницы: 4

Бренд: Zenoah Страницы: 17

Бренд: Makita Страницы: 22

Бренд: Makita Страницы: 36

Бренд: IDEAL Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды