Summa S 75 Скачать руководство пользователя | Manualshive

Страница: 71 / 103

background image

S CLASS™ cutter

User’s Manual

Contour Cutting

3-11

3.3.6

Cutting the contour

1.

Make the layer containing the contour lines visible and printable. Do the opposite
with the print data.

2.

Make sure that the origin marker is also defined as a contour. This will be used as
the origin for the cutting.

3.

Once you are using the cutting software, it may be necessary to collectively rotate
the contours and markers so that the Origin marker (1) is situated in the bottom left
corner of the cutting area (2) as viewed on the screen. If your cutting software’s
default orientation is not set to “landscape,” the contours and markers will need to
be rotated.

1

2

1

2

Orientation needed in most cutter software.

Orientation when using WinPlot

4.

Make sure that the cutter is connected to the computer and that the cutter is
switched on. The cutter’s touch screen should indicate that the cutter is ONLINE.

5.

Click

Cut

from within the cutting software. The cutter should begin cutting the

contour and return to ONLINE

status when finished.

«
...
69
70
71
72
73
...
»

Содержание S 75








































































































Отзывы:

Нет отзывов

Похожие инструкции для S 75

Бренд: Efco Страницы: 100

Бренд: ZIPPER MASCHINEN Страницы: 42

Бренд: Daewoo Страницы: 49

Бренд: ARCBRO Страницы: 28

Cabrio 115306026

Бренд: McCulloch Страницы: 21

Бренд: Echo Страницы: 8

Бренд: Echo Страницы: 44

Бренд: Echo Страницы: 52

Бренд: Echo Страницы: 62

Бренд: SIRI Страницы: 16

Бренд: Ioline Страницы: 8

Бренд: Mafell Страницы: 57

Бренд: Kaiser Страницы: 2

Бренд: Raytools Страницы: 25

Бренд: Eclipse Страницы: 13

Бренд: Ozito Страницы: 2

Бренд: Land Pride Страницы: 38

Бренд: Tasco Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды