Summa S 75 Скачать руководство пользователя

Страница: 22 / 103

S CLASS™ cutter

User’s Manual

Setup

1-12

1.4.1.2 Connecting the S CLASS™ cutter to a Mac using a USB cable

Mac OS 8.5 to OS 9.2

Power off the cutter.

Connect one end of the USB cable to a USB port on the computer.

Connect the other end of the USB cable to the USB port on the back of the

cutter.

Power on the cutter (see section 1.3.3) and return to the computer.

Insert the S CLASS™ CD into the computer’s CD-ROM drive.

Click on the “USB install driver” icon on the CD-ROM.

This will automatically install the driver and the Summa Port Mapper utility.

Remove the CD from the CD-ROM drive.

Restart the computer.

NOTE:

If the cutter is connected to the computer before device installation, then the

computer will regard the cutter as an unknown device. The driver can be installed at
any time with or without the cutter connected.

Mac

OSX

Most recent cutting software does not need a driver installation when a computer is
connected to the cutter. The software that controls the driver is built into the cutting
software.

Содержание S 75








































































































Результаты поиска

Содержание S 75

Отзывы:

Похожие инструкции для S 75

Бренды по названию

Популярные бренды

Summa S 75, Руководство пользователя

Результаты поиска

Содержание S 75

Отзывы:

Похожие инструкции для S 75

Бренды по названию

Популярные бренды