46
MAINTENANCE
6.1
MAINTENANCE SCHEDULE
COMPRESSORS
PROCEDURE
FREQUENCY (HOURS)
SEE NOTE
REF.
D
A
ILY
50
1,000
2,000
4,000
6,000
8,000
10
,0
00
CHECK LUBRICANT LEVEL
X
3
OBSERVE CONTROL PANEL
X
4
---
CHECK FOR LEAKS
X
4
---
INSPECT RETURN LINE FLOW
X
4, 6
---
CHANGE OIL FILTER
X
X
2, 5
CLEAN AIR/OIL COOLER FINS
X
7
CLEAN RETURN LINE SCREEN
X
---
PULL FIRST LUBRICANT SAMPLE
X
8
CHANGE AIR FILTER ELEMENT
X
9
LUBRICANT SAMPLES
X
8
INSPECT COUPLING ELEMENT
X
6
---
INSPECT SOLENOID VALVE
X
6
---
INSPECT MINIMUM PRESSURE VALVE
X
6, 10
TIGHTEN ELECTRICAL CONNECTIONS
X
6
---
VERIFY GAUGE ACCURACY
X
6
---
CHANGE SEPARATOR ELEMENT
X
1, 11
CHANGE LUBRICANT - PALASYN 45
X
8
CHANGE LUBRICANT - PAL-32 LL FOOD GRADE
X
8
CHANGE LUBRICANT - PAL-EXTRA 68
X
8
CHANGE LUBRICANT - PAL-EXTRA 44
X
8
CHANGE LUBRICANT - PALLUBE 32P
X
8
INSPECT ELECTRICAL CONTACTS
X
6
---
INSPECT INTAKE VALVE
X
6
---
GREASE MOTOR
12
---
NOTES
1
50=Weekly, 1,000=Quarterly, 2,000=Biannually, 4,000=Yearly
2
Once, after initial 50 hours from installation
3
Checked with compressor off–sight glass full; checked while
running– any level in sight glass and unit not running hot
4
Compressor running fully loaded
5
Or 15 psid on differential
6
Correct as needed
7
More often, if needed
8
As directed by oil analysis report*
9
Or red indication on vacuum gauge
10
Use lithium grease putting back together
11
Or 10–15 psid on differential
12
Per manufacturer’s specification
*Fluid Life vs. Operating Temperature is only a guideline for typical oil life if temperature is the only variable to be considered.
See
Chapter 8.4.8 Oil Coolant Life vs. Operating Temperature on page 65
for reference.
Many variables affect the oil life, i.e.,
environmental impact from various gases, dust and dirt, compressor short cycling, etc.
Sullivan-Palatek recommends oil sampling as the best guide for your fluid change interval.
Changing fluid once a year may
not be adequate or it can be excessive. For this reason an hourly service on lubricants is merely a guide. Please consult your
factory-trained servicing distributor for questions concerning your lubricant life and Sullivan-Palatek’s lubricant sampling
program. See
Chapter 6.6 Oil Sample For Analysis on page 49
for additional information.
Содержание 15D
