Sullivan-Palatek 15D Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 114

background image

36

COMPONENT DESCRIPTION

3.7.2 INLET CONTROL VALVE

The inlet control valve is the main control for air capacity within the air compressor. It is equipped with a

poppet disc for inlet control as well as reverse flow check. The valve is initially opened at start-up by suction
created by rotating screws in the compressor unit. An air signal from the pressure regulating control valve
will modulate the poppet disc when air demand is low. Upon shutdown, the poppet disc closes to eliminate
reverse airflow from the compressor to prevent the compressor unit from turning backwards. The inlet valve
is mounted directly to the compressor unit inlet.

3.7.3 PRESSURE REGULATING CONTROL VALVE

The pressure regulating control valve modulates the inlet valve to match incoming air with output air

demand. The valve is normally closed. It will open when the line pressure rises to the adjustable set point. As
the pressure regulating control valve opens, an air signal is sent to modulate the inlet valve. The pressure
regulating control valve is located off the top of the sump tank lid.

3.7.4 CONTROL PRESSURE SWITCH (CPS)

The control pressure switch controls the opening and closing of the blowdown solenoid valve. The switch is

normally open. An adjustable load and unload setting on the control pressure switch determines the state of
the switch based on air demand. These settings are initially determined by the factory, but can be adjusted
within the limitations of the compressor according to

6.12 Pressure Adjustment on page 54

.

3.8

MONITORING SYSTEM

The monitoring system is a mechanical gauge panel equipped with specific gauges required to monitor

critical outputs for proper operation of the compressor. In an open machine the gauge panel is located on
top of the starter enclosure box. In compressors that have a sound-reducing enclosure, the gauges are
mounted on the outside front panel of the enclosure. For more details about the gauges and controls, refer
to

5.1 Electro-Mechanical Controls on page 42

.

«
...
42
43
44
45
46
...
»

Содержание 15D



















































































































Отзывы:

Нет отзывов

Похожие инструкции для 15D

Бренд: EUROPRO Страницы: 16

Бренд: Clarke Страницы: 10

Бренд: Ironton Страницы: 20

Бренд: Premier Страницы: 11

Бренд: Atlas Copco Страницы: 28

Бренд: Atlas Copco Страницы: 30

Бренд: Atlas Copco Страницы: 32

Бренд: Faller Страницы: 12

Бренд: Atlas Copco Страницы: 94

Бренд: SM ProAudio Страницы: 12

Marshall and TSR H-1322B

Бренд: Humboldt Страницы: 12

Бренд: KAESER Страницы: 246

Бренд: Danfoss Страницы: 20

Бренд: Gardner Denver Страницы: 17

Grasso RC9 Series

Бренд: GEA Страницы: 68

Бренд: Danfoss Страницы: 54

Бренд: Draper Страницы: 22

Бренд: Draper Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды