Sullair Supervisor II Скачать руководство пользователя

Страница: 15 / 34

Section 2

SUPERVISOR

DESCRIPTION

T2 210

MAX 235

Oil temperature and the maximum limit.

If the temperature exceeds the limit a T3 HI

shutdown will occur.

T3 210

MAX 235

Interstage temperature and the maximum

limit. If the temperature exceeds the limit a

T4 HI shutdown will occur.

T4 210

MAX 235

Total hours that the compressor has been

running.

HRS RUN

001234.0

Total hours that the compressor has been

loaded.

HRS LOAD

000987.0

Last fault log. This shows the fault on the

first line and the run hours when the fault

occcured.

T1 HI

@1 234

Next to last fault log. This shows the fault

on the first line and the run hours when the

fault occcured.

T1 HI

@1 204

2.3F STATUS DISPLAYS --- DS---13

By default the line pressure (P2) and discharge

temperature (T1) are shown on the bottom line of

the display, and machine status on the top line.

The following are the various machine status mes-

sages that indicate the state of the compressor:
(Display graphics shown below.)

STOP --- Compressor is off.

STANDBY --- Compressor is off but armed

to start. This state may be entered because

of a power up, or the unload timer had ex-

pired and stopped the machine. NOTE :

The machine may start at any time.

STARTING --- Machine is trying to start.

OFF LOAD --- Machine is running and off

loaded.

ON LOAD --- Machine is running and

loaded.

FULL LD --- Machine is running and fully

loaded. This state is only displayed if the

machine has a full load valve.

RMT STOP --- Compressor is off but

armed to start. The machine will start when

the remote start contact is closed. NOTE :

the machine may start at any time.

SEQ STOP --- Compressor is off but armed

to start. The machine will start when the se-

quencing conditions meet the critera to

start. NOTE : the machine may start at any

time.

This default display appears as follows:

STOP

110 350

If there are alarms active they will alternately be

shown with the default display. The machine status

will be displayed for 2 seconds then the alarms for 2

seconds each. For example:

T1 HI

110 350

To view other status press the DISPLY key. All tem-

peratures and pressures may be displayed as well

as other status information. To scroll through the

displays press the up arrow or down arrow keys.

Up arrow moves to the next display, down arrow

the previous display. To return to the default display

press the display key.

Interstage discharge pressure and line

pressure.

P1 30

P2 110

Oil filter differential pressure and the maxi-

mum limit. If the limit is exceeded oil main-

tenance warning will be displayed.

dP2 4

MAX 20

Pressure before (P4) and after (P3) oil filter.

Содержание Supervisor II



































Результаты поиска

Содержание Supervisor II

Отзывы:

Похожие инструкции для Supervisor II

Бренды по названию

Популярные бренды

Sullair Supervisor II, Инструкция по эксплуатации

Результаты поиска

Содержание Supervisor II

Отзывы:

Похожие инструкции для Supervisor II

Бренды по названию

Популярные бренды