Suitmate Swimsuit Water Extractor 115V, Установка и обслуживание

Страница: 7 / 58

©2017 Extractor Corporation 115-V 20-Amp 60-Hz SUITMATE ® Unit
5
PROPER DRAINAGE FOR THE SUITMATE ® UNIT
Note: Strictly follow all applicable local plumbing codes and regulations.
TO A FLOOR DRAIN
Drainage of the wastewater to a À oor drain should be done ONL < in an area where the À oor is normally wet.
DO NOT drain water across a À oor where people do not expect to encounter a wet and slippery condition. The
SUITMATE
®
unit comes with a short À exible drain extension tube connected with a stainless steel hose clamp
to its drain tailpiece.
WARNING!
7K e GUD in tu E e t KD t F o P e V Z it K t K e unit P u V t not E e U e P o Y e G un O e VV t K e unit i V
F onne F te G to D n DSSU o Y e G ZDV te ZD te U out O et o U t K e IDF to U\V u SSO ie G tu E e i V
U e SODF e G Z it K D not K e U tu E e DFF o UG in J to t K e I o OO o Z in J in V t U u F tion V .
Replacing the Factory Drain Tube with a Longer Drain Tube
Use a 1-1/4 inch (31.75 mm) I.D. drain tube with a smooth interior that will not crimp or collapse. Use the
stainless steel hose clamp that is provided with the factory
À exible À oor drain extension tube to secure the
replacement tube to the unit’s drain tailpiece. Route the drain tube so that it is never higher than the bottom of
the SUITMATE
® unit and always slopes down. Secure the drain tube to the wall or À oor with properly sized ³ U”
clamps so it cannot be maneuvered to trap wastewater. Cut off the end of the drain tube on an angle to help
prevent it from being blocked by the
À oor, wall, or some other object. Upon completion of the installation,
check to make certain that there is a free À ow of water from the drain tube extension.
TO AN APPROVED SANITARY WASTE LINE
This installation should only be done in accordance with all applicable local plumbing codes and regulations.
The unit’s 1-1/4 inch (31.75 mm) O.D. drain tailpiece is designed for connection with standard compression
type plumbing
¿ ttings. There is room inside of the stainless steel housing for the use of a standard ³ P” type
plumbing connection. The waste outlet should be located in the wall behind the unit. The UTILITIES
LOCATION DIAGRAM (page 8) shows the appropriate location for the waste duct.
PROPER ELECTRICAL CONNECTIONS FOR THE SUITMATE
®
UNIT
Note: Strictly follow all applicable local electrical codes and regulations.
The SUITMATE
®
unit is equipped with a ground fault circuit interrupter (GFCI), that is designed to be
connected to a 115-V 20-Amp 60-Hz dedicated circuit that is protected by a fuse or circuit breaker of the
correct (20 Amp Maximum) size. A PLUG-IN INSTALLATION IS NOT ACCEPTABLE! The utilized circuit must
be run to the SUITMATE
®
unit’s weatherproof Junction Box that contains the GFCI. A liquid tight raceway/
À exible conduit should be used from the circuit connection to the GFCI Junction Box. The UTILITIES
LOCATION DIAGRAM (page 8) shows the location of the suggested area behind the unit for the entrance of
the electrical raceway/
À exible conduit that does not interfere with the drainage connection.
Remove the cover of the weatherproof Junction Box, which contains the GFCI, and remove the GFCI
mounting screws. The circuit ground conductor must be connected to the green grounding screw located on
the GFCI. If no ground is available on the circuit utilized, you must provide a proper ground for the SUITMATE
®
unit. The hot and neutral leads of the power circuit should be connected to the GFCI screw terminals marked
³ LINE”. Connect the hot lead to the terminal marked ³ HOT WIRE” and the neutral lead to the terminal marked
³ WHITE WIRE”. After the correct electrical connections have been properly made, remount the GFCI using
the screws previously removed. Reinstall the weatherproof Junction Box cover previously removed. This cover
provides access to the GFCI
³ TEST” and ³ RESET” buttons.
WARNING!
' o not U oute t K e UDF e ZD\F on G uit ZK e U e ZDV te ZD te U FD n À o Z o U GU i S on it.