©2017 Extractor Corporation
115-V 20-Amp 60-Hz SUITMATE
®
Unit
45
REMOVE AND REPLACE TIMER
'
o t
K
i
V
),567
Make certain you have all the necessary parts and fasteners necessary for correct installation. Parts used in
this process: (1) AEC1419 Timer, (4) AEC1809 Nylon Spacers, (2) AEC1808 Star Lock Washers, (2) AEC1804
S.S. Nuts, (2) AEC1831 Machine Screws, (1) AEC1250 Gasket, and (1) AEC1245 Micro Switch Box Cover.
REMOVE TIMER
1) Turn off the main electrical power to the unit – place a lockout tag on the circuit breaker panel indicating that
the breaker is not to be turned on except by authorized personnel and disconnect the unit before doing any
work on the SUITMATE
®
unit. Simply turning off a switch is NOT enough.
2) Remove SUITMATE
®
unit from the Wall Mount Bracket. See instructions beginning on Page 14. Place the
SUITMATE
®
on its front side.
3) Remove the Micro Switch Box Cover to expose the Micro Switch and Riser Cable lower assembly by
unscrewing (2) screws. Place the screws aside for reassembly.
4) Remove the (2) Nuts, (2) Lock Washers and (4) Spacers to access the Timer. Set the hardware aside for
reassembly.
5) Remove the Timer from the mounting studs.
REPLACE TIMER
1) Remove the wires (see SUITMATE
®
WIRING DIAGRAM on page 6), one at a time, and put each wire on
the appropriate connection on the new Timer.
Note:
Please verify the style of Timer, and use the correct wiring diagram.
2) Place the newly wired Timer on the mounting studs. Use the (4) Spacers (2) Nuts, and (2) Lock Washers
previously removed to secure the new Timer.
Note:
Do not over tighten the Nuts!
3) Replace the Micro Switch Box Cover and secure it in place using the previously removed screws.
WARNING!
0DN
e
F
e
U
t
D
in t
K
e
I
o
DP
V
e
DO
on t
K
e
0
i
FU
o
6Z
it
FK
%
o
[
&
o
Y
e
U
i
V
not
GDPDJ
e
G
V
o
t
KD
t
ZD
te
U
FD
nnot ente
U
t
K
e
0
i
FU
o
6Z
it
FK
%
o
[
.
4) Reinstall the SUITMATE
®
unit to the Wall Mount Bracket. See instructions beginning on Page 14.
5) Turn on the main electrical power to the unit and retest to assure proper operation. Refer to TESTING
AND OPERATION on Page 7.
HOW TO BYPASS THE TIMER
In troubleshooting the SUITMATE
®
unit, it is sometimes necessary to bypass the Timer. In this instance, you
will
¿
rst need to remove the unit from the wall as the Timer is located on the back side of the unit.
Please follow the instructions beginning on Page 14 of this manual to remove the SUITMATE
®
unit from the
wall and to disconnect applicable plumbing and electrical
¿
ttings.
For testing purposes only, the Timer can be bypassed using the following procedure:
1) The black wire connected to #22 (or #2) on the Timer and the black wire connected to #4 (or COM) on the
Timer should be removed off of the Timer and wired together.
2) After connecting the two wires together, restore power to the unit and re-test it. If the issue has been
resolved, your Timer needs to be replaced. If the issue remains, please consult the TROUBLESHOOTING
GUIDE in this manual for further instruction.
WARNING!
0DN
e
F
e
U
t
D
in t
K
e
I
o
DP
V
e
DO
on t
K
e
0
i
FU
o
6Z
it
FK
%
o
[
&
o
Y
e
U
i
V
not
GDPDJ
e
G
V
o
t
KD
t
ZD
te
U
FD
nnot ente
U
t
K
e
0
i
FU
o
6Z
it
FK
%
o
[
.
Содержание Swimsuit Water Extractor 115V
Страница 1: ...115V 60Hz Manual Installation Maintenance...
Страница 2: ......
Страница 57: ......
Страница 58: ...v052017...
