07
Sr.
No.
Parameter setting method
Description of parameters and functions.
Parameter
P5
Parameter
Use UP/DOWN keys to set desired
value.
Example
:
In time it may be possible that the
display may be offset by a degree or so.
To compensate for this error, you may
need to add or minus the degrees
required to achieve the correct
temperature.
The temperature on the
O
display is 28.0 C, whereas the actual
O
temperature is 30.0 C. You will need to
O
set this parameter to 2.0 C, which
means that once out of the programming
parameter, the display will show the
O
O
O
temperature 30.0 C (28.0 C + 2.0 C).
To change P5
press the set key.
parameter,
05
Function: To set probe calibration.
-10.0ºC
10.0ºC
0.0ºC
Range
Min
Max
Fact. Set
P6
Parameter
Use UP/DOWN keys to set desired value.
Example
:
This parameter is used to protect the fan
from restarting in a short period of time
and can be set between 0 to 20 minutes.
If this parameter is set at 3
minutes, the compressor will cut off at
the set temperature, but will not restart
for a minimum of 3 minutes, even if the
differential is achieved earlier. This
To change P6
press the set key.
parameter,
06
Function : To set time delay between
relay restart time.
1 Min
20 Min
3 Min
Range
Min
Max
Fact. Set
Use UP/DOWN keys to set desired value.
Example(Cooling Mode) :
If the set
0
point is set at 10.0 C and differential is
0
set at 2.0 C, then when the system
0
reaches 10.0 C, the comp. relay will
0
cutout. Since the differential is 2.0 C, the
0
comp. Relay will cutin at 12.0 C
0
0
(10.0 C + 2.0 C).
04
P4
Parameter
Function: To set the differential for
compressor restart.
To change
P4
press the set key.
parameter,
0.5ºC
20.0ºC
2.0ºC
Range
Min
Max
Fact. Set
08
Sr.
No.
Parameter setting method
Description of parameters and functions.
Parameter
P7
Parameter
07
Function : To set duration of defrost.
To change the P7 Parameter,
press the set key.
Use UP/DOWN keys to set desired value.
0 Min
99 Min
30 Min
Range
Min
Max
Fact. Set
This is maximum amount of time allowed
for defrost. If set to 0, there will be no
defrost cycle
Example :
If P7 is set to 30 Mins and
P8 parameter is set to 1 Hr. then after
every 1 Hr defrosting will take place for
30 mins. In defrosting Compressor ,
Evap Fan relay willl be OFF.
P8
Parameter
08
Function : To set defrost frequency.
To change the P8 Parameter,
press the set key.
Use UP/DOWN keys to set desired value.
1 Hrs
31 Hrs
6 Hrs
Range
Min
Max
Fact. Set
This is the amount of time between two
defrost cycles.
Example :
same as P7 parameter.
P9
Parameter
09
Function : To set power on defrost delay.
To change the P9 Parameter
parameter, press the set key.
Use UP/DOWN keys to set desired value.
0 Min
99 Min
30 Min
Range
Min
Max
Fact. Set
This is the amount of time at power on
after which defrosting will take place
once.
Example :
If P9 parameter is 30 mins
then at power after 30 mins defrosting
will take place once.
parameter is good to protect the life of
the compressor when there are power
fluctuations and the compressor is
switched off and on within a few seconds.
