Stryker 6390, Руководство по обслуживанию

Страница: 14 / 138

Fuse LITTELFUSE 0496060.ZXD-UL
Standards ANSI/AAMI ES60601-1:2012, CAN/CSA-C22.2 No.
60601-1:14, KKK-A-1822F, IEC 60601-1-12:2014
For standards that require specific options, see
Standards with required options (page 9).
Stryker reserves the right to change specifications without notice.
The yellow and black color scheme is a proprietary trademark of Stryker Corporation.
Hereby, Stryker declares that the radio equipment type short range device is in compliance with Directive 2014/53/EU. The
full text of the EU declaration of conformity is available at the following internet address: http://techweb.med.strykercorp.
com/EMS/EU%20Declaration%20of%20Conformity/index.html.
Labels may be unreadable from a viewing distance greater than 12 inches.
W WA AR RN NIIN NG G
• Do not operate P Po ow we err--L LO OA AD D with a voltage that is inconsistent with the rating on the product.
• Do not operate P Po ow we err--L LO OA AD D above its duty cycle to avoid the risk of equipment damage or smoke hazard.
• Do not connect P Po ow we err--L LO OA AD D to a 24 VDC vehicle circuit. Always connect P Po ow we err--L LO OA AD D to a 12.8 VDC-15.6 VDC
vehicle circuit that is on a 15A fuse/breaker to prevent power hazards.
• P Po ow we err--L LO OA AD D operates at 13.56 MHz when you use P Po ow we err--L LO OA AD D controls with a powered cot (P Po ow we err--P PR RO O XT or
P Po ow we err--P PR RO O IT) that could interfere with other equipment that operate at this frequency band.
• The use of accessories, transducers, and cables, other than those specified, with the exception of transducers and
cables that are sold by Stryker as replacement parts for internal components, may result in increased emissions or
decreased immunity of the P
Po ow we err--L LO OA AD D system.
• Do not use the P Po ow we err--L LO OA AD D system and the P Po ow we err--P PR RO O cot adjacent to or stacked with other equipment. If adjacent
or stacked use is necessary, observe the P Po ow we err--L LO OA AD D system to confirm normal operation in the configuration where it
will be used.
• P Po ow we err--L LO OA AD D operates primarily at these frequencies: 70 - 85 kHz for inductive charging and 13.56 MHz±7 kHz,
Amplitude Modulated (OOK), ERP: -82.37 dBm. The inductive charging can operate between these frequencies: 70 -
125 kHz. Other equipment may interfere with the P
Po ow we err--L LO OA AD D system, even if that other equipment complies with
CISPR emission requirements.
E En nvviirro on nm me en ntta all cco on nd diittiio on nss
O Op pe erra attiio on n S Stto orra ag ge e a an nd d ttrra an nssp po orrtta attiio on n
Temperature
130 °F
(54 °C)
-30 °F
(-34 °C)
158 °F
(70 °C)
-30 °F
(-34 °C)
Relative humidity
93%
0%
93%
0%
Atmospheric pressure
1060 hPa
700
1060 hPa
700
C CA AU UT TIIO ON N
• This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at their expense. In the event of interference, please relocate or
reorient the P
Po ow we err--L LO OA AD D system or interfering product.
• Always relocate or reorient the P Po ow we err-- L LO OA AD D system or interfering product in the event of interference. This device
complies with Part 18 of the FCC Rules.
EN 8 6390-309-002 Rev AB.0