background image

Page 7 of 19 

 

Specific Operation Warnings 

 

CRUSHING AND LACERATION HAZARD 

 

Implement is heavy. Be careful when moving or lifting as hands, finders, feet, and other body 
parts can be crushed. 

 

Implement has sharp spikes. Keep hands clear as these spikes can cut. 

 

DO NOT exceed this implement’s maximum speed of 5 MPH. Exceeding this speed may result in 
loss of control during transport or braking. 

 

Never allow riders on equipment. 

 

Keep bystanders at least 20 feet away while operating. 

 

Operate from tractor seat only. 

 

Lower equipment to ground, stop engine, remove key and set brake before dismounting tractor. 

 

DO NOT use if equipment is damaged. Repair equipment before continuing use. 

 

Keep seat belt securely fastened while operating.  Falling off can result in impalement or being 
run over.  

 

Sharp points can cause injury. Be cautious when replacing tines. 

 

Store out of reach of children. Not for use by or around children. 

 

If equipped, parking stands must be functional, kept in good repair, and stored on the unit. Park 
and store on a hard, level surface. 

FALLING OFF CAN RESULT IN IMPALEMENT OR BEING RUN OVER 

 

Tractor must be equipped with Roll Over Protection Structure (or ROPS CAB) and seat belt. Keep 
foldable ROPS system in “locked up” position at all times. 

 

Keep seat belt securely fastened. 

 

Never allow riders on equipment. 

 

Raised equipment can drop and crush. 

 

Before working underneath, follow all instructions and safety rules in operator’s manual and 
securely block all corners of equipment with jack stands. 

 

Securely blocking prevents equipment dropping from mechanical component failures. 

FALLING OFF OR FAILING TO BLOCK SECURELY CAN RESULT IN SERIOUS INJURY 

OR DEATH 

 

Содержание 49167




















Отзывы: