Strongway 46270 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 23

background image

7

3. Put the frame in an upright position, and attach the upper crossbeam (14) and attached the springs

(15). Then attach eye hooks (17), using nuts (20) to middle bolster (18). The attach springs to middle

bolster. (Middle Bolster will then suspend between left and right frame posts.)

4. Carefully place 12 ton hydraulic bottle jack (16) in between the middle bolster (15) and upper

crossbeam (14). Adjust the nuts (20) to the proper position once jack has been installed.

«
...
5
6
7
8
9
...
»

Содержание 46270
























Отзывы:

Нет отзывов

Похожие инструкции для 46270

Бренд: Makita Страницы: 3

Бренд: ODA Страницы: 113

Бренд: PAC Страницы: 2

VisionXS-IP-F-DP-UHR

Бренд: G&D Страницы: 148

Бренд: Unior Страницы: 2

Бренд: Unior Страницы: 4

Бренд: K-BUS Страницы: 35

Бренд: Placid Industries Страницы: 4

Бренд: Grizzly Страницы: 48

Бренд: Milwaukee Страницы: 45

Бренд: Cetacea Sound Страницы: 2

Бренд: SilverStone Страницы: 12

Бренд: Textron Страницы: 8

GC-CG 3,6 Li WT

Бренд: EINHELL Страницы: 72

Бренд: AP&T Страницы: 3

Бренд: Magswitch Страницы: 2

Бренд: MAG TOOLS Страницы: 2

Бренд: King Canada Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды