Strongway 46270 Скачать руководство пользователя страница 19

Страница: 19 / 23

LUBRICATION

A periodic coating of light lubricating oil to pivot points will help to ensure that pump piston linkages move

freely.

Note: Never apply oil to the saddle. If saddle extension threads require lubrication; clean thread surfaces

with a clean, dry cloth, then apply a drop of bearing grease to the threads. Distribute as evenly as

possible along the threaded post.

TROUBLESHOOTING

JACK

WILL

NOT
LIFT

LOAD

JACK

WILL

NOT

HOLD
LOAD

JACK

WILL NOT

LOWER

POOR JACK

LIFTING

WILL NOT LIFT

TO FULL

EXTENSION

CAUSES AND SOLUTIONS



 





Release valve is not completely closed (Turn
handle clockwise).

 



Weight Capacity Exceeded.

 

 



Air is in the hydraulics.
Purge air from system.

  



Low oil level. Add oil as required.



 



Oil reservoir is overfilled:
Drain excessive oil.
Lubricate moving parts.



 



Jack is binding or foreign obstruction











Power unit malfunctioning.
Replace the power unit.

Содержание 46270
























Результаты поиска

Содержание 46270

Отзывы:

Похожие инструкции для 46270

Бренды по названию

Популярные бренды

Strongway 46270, Руководство пользователя

Результаты поиска

Содержание 46270

Отзывы:

Похожие инструкции для 46270

Бренды по названию

Популярные бренды