Stover SGH 140 RV, Инструкция по применению

Страница: 36 / 80

36
Solution:
Check whether butane or propane is being used: butane will burn ever more poorly as the temperature drops below 7 °C because it then turns
into liquid. With LPG (= propane/butane mixture), it will often help to give the gas cylinder a shake.
Use only a correct low pressure regulator. Outlet pressure details: see rating label. Do not move the appliance when operating, shocks and
bumps may activate the safety device. Do not twist the flexible tubing or hose.
USE
The knobs for turning the gas heater ON are located on the upper part of the heater:
• Open the gas container (follow the user instructions provided with the low-pressure regulator).
• See the fig. Turn the regulation knob (5) into position 1. Press button (5) down for 20 seconds. After 20 seconds: keep pressing button 5
down and at the same time, press the piezoelectric button (4) a few times until the small blue pilot flame at the lower end of the front of the
heater is visible. KEEP PRESSING DOWN BUTTON (5) for another 20-40 seconds.
After 20-40 seconds: the button 5 can be released (keep it in position 1). If the pilot flame disappears: repeat the procedure. Especially with
a new gas bottle OR when the heater is not used for a couple of days this procedure could take a couple of times because the gas must flow
from the gas bottle through the gas tube towards the pilot flame first!
After button (1) is released: the button can now be turned to the desired heating position: (2) medium heat or (3) maximum heat.
1. minimum
2. medium
3. maximum
4. ignition
5. regulation knob
Release the knob and turn it to the position corresponding with the desired amount of heat:
• To turn OFF the device, close the gas container valve.(follow the instructions provided with the low-pressure regulator).
• Do not hold the regulation knob pressed down for longer than 40 seconds.
• Never move the heater when it is hot and/or in operation.
GAS LEAKS
If you think there may be a gas leak, please follow this procedure:
• Close the gas container valve. (follow the user instructions for the regulator);
• Extinguish all open flames, for instance stoves;
• Open windows in order to increase airflow circulation;
• Turn off electrical devices, for instance lamps;
• Prepare a bucket of soapy water;
• Open the gas container (follow the user instructions for the regulator);
• Brush the soapy water on all fittings and connections of the gas circuit;
• If there is a gas leak, bubbles will rise up from the location of the leak;
• If a leak is found, close the gas container (follow the user instructions for the regulator).
• Tighten the fitting and the metal rings of the connection;
• Open the gas container (follow the user instructions for the regulator) and repeat the procedure again.
If there is still a gas leak contact a professional and qualified engineer for help.
SAFETY TIPS 2
• Always place the heater facing the center of the room.
• Do never move the heater when it is burning.
• Prevent people, especially young children and elderly people from touching very hot surfaces.
• Never dry clothes at the top of the metal guard grill
• Keep all flammable materials at least one meter away from the heater.
• Never use a gas heater in a bathroom, bedroom, mobile home, high rise buildings or caravan. Toxic gases may cause serious health problems
in these situations.
• Never use or store solvents and pressure pack cans near a gas heater, even if the heater is turned off.
• Never dispose of rubbish such as cigarette butts in a gas fire -this can affect combustion and produce dangerous pollutants.
• Make sure rooms containing gas heater are well ventilated.
• Keep areas around the heater free of papers, trash, and any other combustible items
• Place the heater on a level, hard, nonflammable surface; do not place on rugs, carpets or socket, near bedding or drapes, or on tables or countertops.
• Turn the heater off if you leave the area, and never leave a heater on while sleeping or if you leave home.
• Always use specified or standard wire, plug and socket, always protect them from moisture or water.
• Always turn off gas valve and remove the plug after use.
• Always make sure that you actually see the appliance when you want to switch it on. Never use things like a timer, programmer or any other
device (including Internet apps) that switches on the appliance automatically as this may cause fire!
CLEANING AND MAINTENANCE
Before cleaning, turn the gas heater OFF and wait until it has cooled down completely. To clean the outside of the heater, use a soft cloth
dampened with water and liquid detergent. Never use scouring pads or abrasive products. Do not use water, inflammable or abrasive cleaners.
3
1
2
5
4
ASSEMBLING THE GAS HEATER
• Carefully remove your heater from the box and check the contents. In addition to the heater you should also have: Directions for Use for the
gas heater
• Remove all other packaging materials and check the heater for any damage. If you have any doubts concerning the heater, please contact
qualifi ed service personnel. Keep all packaging material out of the reach of young children.
• Assemble the heater as mentioned at PIC 2 to PIC 8 in the first pages of this instruction manual.
• Before connecting the low-pressure regulator, please check and read the following: The gas heater should only be powered by Propane-
Butane in a container with a maximum weight of 15kg. Connect the low-pressure regulator with a fi xed calibration of maximum 30 mbar
that complies with EN16129. The hose should be according to national standards. For correct connection, the hose should be connected using
metal bands of a suitable size. For correct connection, follow the instructions provided with the low-pressure regulator.
• Slide the two metal rings around the hose. Connect the hose to the hose union of the low-pressure regulator and to that of the tab. Close
the metal rings fi rmly with a screw, but make sure that you do not damage the fi tting or any component.
• Before connecting the low-pressure regulator to the gas container, make sure that the gas container is closed and that there are no open
fl ames (i.e. a lit oven) in the place where you are working. Connect the low-pressure regulator according to the user instructions that are
provided with the low-pressure regulator.
Check for gas leaks: see section F
• Place the gas container in its compartment. Take care that the hose is not twisted or obstructed, and that it is unable to touch any hot parts
of the heater.
• Hook the rear cylinder cover onto the compartment by inserting the two hooks into the respective holes of the cabinet.
1. Burner effect regulator
2. Gas Main Valve
3. Gas Hose
4. Gas Pressure regulator
5. Protection baffl e
6. Gas Cylinder
In addition
• To replace the gas container, make sure that the gas container is closed (follow the user instructions provided with the low-pressure
regulator). Let the gas heater cool down first and make sure that there are no open flames or other sources of heat in the area in which you
are working.
• Only change the gas container in a flame free environment.
• In addition it is recommended that the gasket seals of the regulator and the flexible rubber hose be checked to ascertain their condition. If
you have any doubt concerning the condition of the hose or the seals, replace them.
• Make sure that you do not damage the connection or any other components;
• Never turn the gas container upside down in order to make full use of the contents. This may release liquid residues left in the container that
damage the heater irreparably;
• For disconnection or connection of the low-pressure regulator, always follow the user instructions provided with the regulator;
• The manufacturer is not responsible for any harm or damage if attention is not paid to the points described above.
• Do not twist the flexible tubing or the hose.
INSTALLATION
• Use the gas heater in well-ventilated rooms only. A minimum room size of 85m³ is recommended for living rooms and 50m³ for other rooms,
but the room should never be less than 50m³. For ventilation 2x a surface of 50cm² ventilation openings are required.
• The room in which the gas heater is used should have enough air circulation for normal combustion. Therefore it is required that the room
must be provided with a grand total of >100 cm² of all ventilation openings.
• Always place the heater on a flat and stable surface. Never install or use the heater in a bathroom or bedroom, in the basement, on the
upper floors of a building or in leisure accommodations;
• Never position the gas heater too close to other sources of heat (a distance of at least 1 metre is required between the gas heater and other
heating sources) or inflammable or explosive materials. During operation, the gas heater should not face objects that can be damaged or
burned;
• Position the heater so that the heat is directed towards the center of the room and towards an open space. In addition, the front, radiant
part must be at least 2.0 meter away from any inflammable materials, i.e. curtains or sofas;
• Never operate the gas heater when the gas container is outside the compartment.
• Only replace gas cylinder in a flame free environment.
• Before connecting the gascontainer to the device
o Check and clean the filter of the regulator
o Release a little bit of gas (outdoors) from the gascontainer. This will clear present dirt particles to prevent them from entering the pressure
regulator or device.
• Each time when gas cylinder or gas tube is connected: always do a leakage test with soapy water - see chapter 'gas leaks'.
Problem:
No flame/no ignition in winter (temp. <7 °C)
4
man_SGH140RV ('20) V4.indd 36 man_SGH140RV ('20) V4.indd 36 30-06-20 14:45 30-06-20 14:45