background image

Chapter 2. Installation

Order Number:  EK–SMCPC–UG. A01

2–7

able for the ac distribution unit. Since these power cords are country specific, ensure that
your power cord matches those listed in Table 2–2 for your installation.

In general, the power cords listed in Table 2–2 have the following characteristics:

Rated at 10 amps at the specified operating voltage

2.5 meters (8.2 feet) in length

Have a country-specific plug

Have an IEC 320 C-14 compatible connector

The only exception is the BN27S-03 power cord used in Japan and the United States; it
is rated at 15 amps and is 3 meters (9.84 feet) long.

Table 2–2  Country-Specific Power Cords

Country

Voltage

Plug

Length meters (ft.)

Part No,

Australia

250 Vac

AS 3112 - 1981

2.5 (8.2)

BN19H-2E

Central Europe

250 Vac

CEE 7/7 (Schuko)

2.5 (8.2)

BN19C-2E

Denmark

250 Vac

Afsnit

2.5 (8.2)

BN19K-2E

India

250 Vac

BS 546

2.5 (8.2)

BN19S-2E

Ireland

250 Vac

BS 1363

2.5 (8.2)

BN19A-2E

Israel

250 Vac

SI 32

2.5 (8.2)

BN18L-2E

Italy

250 Vac

CEI 213-16/VII

2.5 (8.2)

BN19M-2E

Japan

125 Vac

NEMA 5-15

3.0 (9.8)

BN27S-03

1

New Zealand

250 Vac

AS 3112 - 1981

2.5 (8.2)

BN19H-2E

South Africa

250 Vac

BS 546

2.5 (8.2)

BN19S-2E

Switzerland

250 Vac

SEV 1011

2.5 (8.2)

BN19E-2E

United Kingdom

250 Vac

BS 1363

2.5 (8.2)

BN19A-2E

United States

125 Vac

NEMA 5-15

3 (9.8)

BN27S-03

1

This power cord is rated at 15 amps.

To connect the power cord to the pedestal refer to Figure 2–5 and proceed as follows:

1. Open the door on the front bezel and ensure the power switch on the ac distribution

unit is set to off.

2. Remove the rear bezel as described in Section 4.5.1.

3. Route the female end of the power cord under the handle of the pedestal base and

connect the cord to the ac receptacle on the ac distribution unit.

4. Replace the rear bezel as described in Section 4.5.2.

5. Close the door on the rear bezel and connect the other end of the power cord to an ac

outlet.

6. If installing SBBs, proceed to Section 2.4.3. If the pedestal is preconfigured with

SBBs, proceed to the power-on test in Section 2.5.

Содержание SWXSE-22



























































Отзывы: