Stone XD836Y Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 98

background image

- 54 -

7.3 INSTRUCTIONS FOR SERVICE

LOWER UNIT XN OIL INJECTED AND PRE-MIX

STOMPER MODEL XN650

1.

Detach the shoe from the stomper by removing (6) shoe bolts and washers.

2.

Thread M8 nuts onto (2) full thread M8 x 5.50” bolts (provided in kit) 1.25” up from the bottom of the bolts (see
Figure A).

3.

Replace two bolts that are diagonal from each other on the bottom spring cover with assembled full thread bolts with
nuts from Step 2. Make sure to thread the assembled bolts in a full 1.25” (see Figure B).

4.

Remove the other (4) bolts from the bottom spring cover (leaving the full thread bolts in place).

5.

Carefully back each nut off a .25” at a time on each side using two wrenches (one to hold the bolt in place and the
other to back the nut off) until the spring tension is removed (see Figure C).

6.

Then remove the full thread bolts and the bottom spring cover to access the springs.

7.

Remove lower spring set.

8.

Insert snubber puller, P/N 39539, under snubber (Item 14). Insert pry bar under snubber puller and pop loose
snubber.

9.

Using M24 deep socket, remove M16NY locknut from piston rod. Insert 5/8" or smaller rod through top of piston rod
head to hold rod from turning to remove nut.

10. Piston puck and upper springs can now be accessed.

11. Reassemble in reverse order.

* Use red loctite 264 on shoe bolts only.

ITEM

P/N

DESCRIPTION

QUANTITY

KIT

23159

Kit Snubber Puller XN

1

1

56338

Instructions Lower Unit Service XN

1

2

50107

Weld Thread M8 x 5.50 in.

2

3

39539

Puller Snubber

1

4

80854

NUTFX M8-1/25

2

Figure B

Figure C

Figure A

The spring retaining Base Plate retains heavy springs
under compression. Follow the instructions carefully
or severe personal injury may occur.

«
...
52
53
54
55
56
...
»

Содержание XD836Y



































































































Отзывы:

Нет отзывов

Похожие инструкции для XD836Y

Бренд: Makita Страницы: 20

MAKSTAR BTW250 Series

Бренд: Makita Страницы: 8

Бренд: Haas Automation Страницы: 127

Бренд: London Emblem Страницы: 3

ShopMaster CL180JS

Бренд: Delta Страницы: 15

Бренд: Larzep Страницы: 8

Бренд: IKA Страницы: 16

Бренд: Neilsen Страницы: 16

CAPSpray 0524000

Бренд: Titan Страницы: 24

Бренд: Phoenix Contact Страницы: 36

Бренд: BVV Страницы: 5

Бренд: Max Страницы: 14

Бренд: Qonnect Страницы: 4

Бренд: Hilti Страницы: 15

Бренд: Wacker Neuson Страницы: 46

Бренд: Ryobi Страницы: 9

Бренд: Yokota Страницы: 44

Бренд: Glendo Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды