Stone XD836Y Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 98

background image

- 26 -

4.3.2 Starter Screen

This screen keeps dirt, etc., from entering the fan housing and clogging the air cooling passages. Be-
cause this engine is air-cooled, it is necessary to keep this screen clean at all times to permit the unre-
stricted passage of air into the fan housing.

4.3.3 Fasteners

Check all nuts and bolts after 4 hours, then every day of operation. See parts lists for recommended
torque values.

4.3.4 Lubrication

The oil level should be checked now and before first use of the Stomper. Thereafter, it should be checked
every day as follows.

FOR XD MODEL

1.

With unit standing upright (in vertical position--not operating) so that the oil drains freely into the
spring housing, check that the oil is at fill sight plug level.

2.

Whenever the level is low, remove the fill sight plug and refill to level of fill sight plug with any good
quality SAE-30 engine oil.

NOTE:

Use of a socket wrench is recommended to avoid damage to the sight gauge.

3.

Change the oil every 300 operating hours or six months.

4.3.5 Air Cleaner

Engine life will be extended by maintaining a clean engine air filter. Remove and clean the air filter
element daily or more frequently under dustier job conditions. Wash the pre-filter element clean in a
non-oily cleaning solvent such as "Solvesol". Let the filter dry before reinstalling it in the air cleaner.

Replace air cleaner element every 100 hours. (More frequently in dusty areas).

4.4 TO START MACHINE

1.

Check fuel tank, engine oil, air cleaner and Stomper lubrication as previously instructed.

CAUTION:

Never use ether or other starting fluids to start the diesel engine. Engine failure will result.

2.

Open the fuel valve under the tank and the air vent thumbscrew in the tank fill cap.

3.

Raise throttle lever about 3/4 throttle.

OIL FILL PLUG & SIGHT GAUGE

«
...
24
25
26
27
28
...
»

Содержание XD836Y



































































































Отзывы:

Нет отзывов

Похожие инструкции для XD836Y

Бренд: Teccpo Страницы: 14

Бренд: Bahco Страницы: 6

Бренд: Dake Страницы: 24

Бренд: Parkside Страницы: 64

Бренд: Parkside Страницы: 44

Бренд: Parkside Страницы: 64

Бренд: Graco Страницы: 2

Бренд: Siser Страницы: 76

Бренд: Eastwood Страницы: 8

Бренд: Wolf Garten Страницы: 198

Бренд: Magswitch Страницы: 2

Бренд: Palmgren Страницы: 4

Бренд: Parkside Страницы: 67

Бренд: Omer Страницы: 2

Бренд: LEVIOR Страницы: 2

Бренд: General integration Страницы: 12

360 IQ HAT PRESS

Бренд: Hotronix Страницы: 16

Бренд: BGS technic Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды