Stone XD836Y Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 98

background image

- 37 -

5.3 PRE-OPERATION CHECKS

CAUTION:

Sections on fuel mixture, air cleaner, and lubrication must be followed exactly. Failure to

follow these instructions may void the warranty.

5.3.1 Spark Plug

Check and clean spark plugs regularly. A fouled, dirty, or carboned spark plug causes hard starting and
poor engine performance. Set spark plug gap as per specifications. See Engine Manual.

5.3.2 Starter Screen

This screen keeps dirt, etc., from entering the fan housing and clogging the air cooling passages. Because
this engine is air-cooled, it is necessary to keep this screen clean at all times to permit the unrestricted
passage of air into the fan housing.

5.3.3 Fasteners

Check all nuts and bolts after 4 hours, then every day of operation. See parts lists for recommended
torque values.

5.3.4 Fuel Mixture

Use recommended fuel mixtures. To get this ratio, thoroughly mix the following quantities of gas and oil
in a clean safety container:

Use regular unleaded gasoline. High test is not recommended.

Strain the fuel mixture through a fine meshed screen when filling gasoline tank on engine to remove dirt
if present.

5.2 OPERATING PRINCIPLE

A tamping shoe is mounted at the lower end of a cylindrical spring housing. A piston, installed between
massive opposing springs inside the spring housing, is actuated by a connecting rod and crank system
which is driven by a high speed, 2 cycle gasoline engine through a gear train and centrifugal clutch.
The piston alternately loads and unloads the springs. This results in a rapid lifting up and ramming down
action of the tamping shoe to compact the underlying material.

The Stomper is effective for compaction of a wide variety of job soil substances, particularly clay lumps,
silt, loam and all granular materials. Although relatively light in weight and easy to operate, the Stomper
delivers a tremendous impact to the soil.

These instructions contain information to guide you in efficient use and proper maintenance of the
Stomper. To get long and trouble-free service from this power tool, periodic maintenance of the engine
and machine is essential.

The Stomper is shipped completely assembled and only requires filling with 2 cycle fuel mixture and a
brief check of lubricant levels in preparation for operation. You should first study these instructions.

OPERATING INSTRUCTIONS

«
...
35
36
37
38
39
...
»

Содержание XD836Y



































































































Отзывы:

Нет отзывов

Похожие инструкции для XD836Y

Бренд: Danfoss Страницы: 8

Бренд: jbc Страницы: 12

Бренд: jbc Страницы: 8

Бренд: Palmgren Страницы: 20

Бренд: TE Connectivity Страницы: 4

Бренд: H&S Страницы: 2

Бренд: Hammerhead Страницы: 60

Бренд: JAMEC PEM Страницы: 4

Бренд: Virutex Страницы: 9

Бренд: FASANO TOOLS Страницы: 8

Бренд: Kett Страницы: 6

PolySprint NPS-1210A-1

Бренд: Nitta Страницы: 22

Бренд: Neilsen Страницы: 4

Бренд: Hewlee Страницы: 8

Бренд: HOKUBEMA Страницы: 69

Бренд: Swivelpole Страницы: 2

Бренд: Stanley Страницы: 20

Бренд: Facom Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды