manualshive.com logo in svg

Stone XD836Y, Руководство оператора и сервисное руководство, Страница: 47 / 98

Поделиться
Скачать
Stone XD836Y Скачать руководство пользователя страница 47

- 47 -

6.6  OPERATION OF MACHINE

WHEN OPERATING THE STOMPER, KEEP FEET CLEAR FROM THE RAMMING
SHOE.  SERIOUS PERSONAL INJURY MAY OCCUR.

WHEN OPERATING THE STOMPER, HEARING PROTECTION SHOULD BE WORN.
HEARING LOSS MAY RESULT FROM PROLONGED EXPOSURE TO NOISE.

CAUTION:

  Never operate on hard, unyielding surfaces.  Unwarranteed damage may result.

CAUTION:

 

 Always use both hands when operating this machine.  This will ensure safe machine operation.

1.

In operation, guide the machine but let the machine do the work.  Bearing down on the handle is
unnecessary and limits the shoe jump.

2.

On nearly level surfaces, the machine moves forward in rapid jumps.  On uneven surfaces or inclines,
rocking the handle slightly may assist the Stomper in moving forward.

3.

Always guide the Stomper so that the whole shoe, and not just the front or back edge, does the
impacting.

4.

As the soil becomes compacted, the jump height of the Stomper will increase.

5.

After a brief experience, you will know how to adapt the technique to the job conditions.

WARNING

Содержание XD836Y



































































































Отзывы:

Нет отзывов