Stone XD836Y Скачать руководство пользователя страница 32

Страница: 32 / 98

- 32 -

4.14 THROTTLE CONTROL CABLE ADJUSTMENT

Loosen throttle cable
clamp screw.

Push throttle handle all
the way to the right.

Push up on high RPM
throttle paddle until it
rests on the high RPM
adjustment screw and
tighten throttle cable
clamp screw.

Run machine and
check engine RPM
with a tachometer to
see if it is running to
specified RPM.

4.15 SETTING HIGH RPM
(Operating Speed)

Loosen throttle control cable clamp screw and high RPM adjustment screw locking nut.

Turn high RPM adjustment screw clockwise to increase RPM or counterclockwise to decrease RPM,
then tighten high RPM adjustment screw locking nut.

Push throttle handle all the way to the right.

Push up on the high RPM throttle paddle until is rests on the high RPM adjustment screw and
tighten the throttle cable clamp screw.

Run machine and check engine RPM with a tachometer.

If engine is still not running to specified RPM, repeat above steps until recommended RPM is obtained.

4.16 THROTTLE HANDLE ADJUSTMENT

Retighten pivot bolt tight enough as to not allow throttle handle to move forward when machine
is operating

4.17 STORING STOMPERS

The following steps should be taken to prepare your Stomper for storage:

Operate engine for about three (3) minutes.

Stop engine. Drain lube oil and fill with clean oil.

Содержание XD836Y



































































































Результаты поиска

Содержание XD836Y

Отзывы:

Похожие инструкции для XD836Y

Бренды по названию

Популярные бренды

Stone XD836Y, Руководство оператора и сервисное руководство

Результаты поиска

Содержание XD836Y

Отзывы:

Похожие инструкции для XD836Y

Бренды по названию

Популярные бренды