manualshive.com logo in svg

Stone XD836Y, Руководство оператора и сервисное руководство


Поделиться
Скачать
background image

4.5

To Stop Machine ........................................................................................................................... 27

4.6

Operation of Machine ................................................................................................................... 27

4.7

Lifting and Transporting ............................................................................................................... 27

4.8

Engine Idle .................................................................................................................................... 28

4.8.1

Fuel System .................................................................................................................... 28

4.9

Disassembly and Reassembly - Fuel Injection Pump .................................................................... 29

4.10 Fuel Injection Valve ....................................................................................................................... 29 - 30

4.11 Disassembly and Reassembly - Case Nut ..................................................................................... 30

4.11.1

Adjustment .................................................................................................................... 30 - 31

4.12 Fuel Filter ...................................................................................................................................... 31

4.13 Speed Control Device .................................................................................................................... 31

4.14 Throttle Control Cable Adjustment ............................................................................................... 32

4.15 Setting High RPM ......................................................................................................................... 32

4.16 Throttle Handle Adjustment .......................................................................................................... 32

4.17 Storing Stompers ........................................................................................................................... 32 - 33

SECTION 5 - OPERATIONS/ROUTINE MAINTENANCE - 2-CYCLE PRE-MIX STOMPER ........................ 35 - 41

5.1

Specifications ................................................................................................................................ 36

5.2

Operating Principle ........................................................................................................................ 37

5.3

Pre-Operation Checks .................................................................................................................... 37

5.3.1

Spark Plug ...................................................................................................................... 37

5.3.2

Starter Screen ................................................................................................................. 37

5.3.3

Fasteners ....................................................................................................................... 37

5.3.4

Fuel Mixture ................................................................................................................... 37 - 38

5.3.5

Oil Pipe Replacement ..................................................................................................... 38

5.3.6

Lubrication ..................................................................................................................... 38

5.3.7

Air Cleaner ..................................................................................................................... 38

5.4

To Start Machine ........................................................................................................................... 39

5.5

To Stop Machine ........................................................................................................................... 39

5.6

Operation of Machine ................................................................................................................... 39

5.7

Throttle Control Cable Adjustment ............................................................................................... 40

5.8

Setting High RPM ......................................................................................................................... 40

5.9

Throttle Handle Adjustment .......................................................................................................... 40

5.10 Idle Setting .................................................................................................................................... 40

5.11 Storing Stompers ........................................................................................................................... 41

SECTION 6 - OPERATIONS/ROUTINE MAINTENANCE - 4-CYCLE GAS STOMPER ................................ 43 - 49

6.1

Specifications ................................................................................................................................ 44

6.2

Operating Principle ........................................................................................................................ 45

6.3

Pre-Operation Checks .................................................................................................................... 45

6.3.1

Spark Plug ...................................................................................................................... 45

6.3.2

Starter Screen ................................................................................................................. 45

6.3.3

Fasteners ....................................................................................................................... 45

Содержание XD836Y



































































































Отзывы:

Нет отзывов

Похожие инструкции для XD836Y

Teryair ENS100V Operation And Maintenance Manual preview
ENS100V
Бренд: Teryair Страницы: 8
Powerfix POWERFIX KH4055 Operating Instructions preview
POWERFIX KH4055
Бренд: Powerfix Страницы: 4
Ranger Products RFJ-3000AL Installation And Operation Manual preview
RFJ-3000AL
Бренд: Ranger Products Страницы: 8
Laguna Tools Dake 972200 Instructional Manual preview
Dake 972200
Бренд: Laguna Tools Страницы: 23
Clas Ohlson PLD7060 Manual preview
PLD7060
Бренд: Clas Ohlson Страницы: 52
G&G Technics GGT-6045 Quick Start Manual preview
GGT-6045
Бренд: G&G Technics Страницы: 2
TE Connectivity SOLISTRAND 69097 Instruction Sheet preview
SOLISTRAND 69097
Бренд: TE Connectivity Страницы: 11
Stihl 4910-500-1800 Instruction Manual preview
4910-500-1800
Бренд: Stihl Страницы: 36
KNIPEX 12 72 190 Operating Instructions Manual preview
12 72 190
Бренд: KNIPEX Страницы: 12
Magnaflux 628554 Operating Manual preview
628554
Бренд: Magnaflux Страницы: 28
Samtec CAT-HT-182-2430-11 Instruction Sheet preview
CAT-HT-182-2430-11
Бренд: Samtec Страницы: 4
Prosharp AS 1001-Portable Original Instructions Manual preview
AS 1001-Portable
Бренд: Prosharp Страницы: 11
Band-it C00269 Quick Start Manual preview
C00269
Бренд: Band-it Страницы: 3
SUHNER ABRASIVE LBB 20 Technical Document preview
LBB 20
Бренд: SUHNER ABRASIVE Страницы: 28
SUHNER ABRASIVE AH 12 Manual preview
AH 12
Бренд: SUHNER ABRASIVE Страницы: 60
Forster Products Co-Ax Primer Seater Instructions preview
Co-Ax Primer Seater
Бренд: Forster Products Страницы: 2
Arrow OSC9500-A User Manual preview
OSC9500-A
Бренд: Arrow Страницы: 32
Josef Kihlberg JK20-670 Operating Instructions Manual preview
JK20-670
Бренд: Josef Kihlberg Страницы: 44

Бренды по названию

Популярные бренды

Загрузить еще бренды