Stone XD836Y Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 98

Stone XD836Y Скачать руководство пользователя страница 21

- 21 -

3.11 STORING STOMPERS

The following steps should be taken to prepare your Stomper for storage:

1.

Disconnect fuel line and allow all fuel to drain from the gasoline tank only. Replace fuel line.

2.

Start engine and allow to run until it stops from lack of fuel. This will use up all the fuel in the
carburetor and prevent the formation of deposits due to evaporation of fuel.

GASOLINE IS BOTH TOXIC AND FLAMMABLE. DO NOT SMOKE WHILE
WORKING WITH FUEL. DO NOT USE NEAR OPEN FLAME. AVOID PROLONGED
BREATHING OF VAPORS AND SKIN CONTACT. FLASH POINT OF GASOLINE
IS 40°F (4°C). SERIOUS ILLNESS OR LOSS OF LIFE COULD RESULT.

3.

Close fuel valve/shut-off switch.

4.

Remove spark plug and pour 60cc or 2 ounces (1/4 cup) of motor oil into the cylinder. Replace
plug.

5.

Crank the engine two or three times to distribute the oil throughout the cylinder. This will help
prevent rusting during storage.

6.

Store the unit in an upright position (as in the operating position) in a cool, dry, ventilated area.

WARNING

«
...
19
20
21
22
23
...
»

Содержание XD836Y



































































































Отзывы:

Нет отзывов