Owner’s Manual #513625
14
SU412 Model Machines
E. SERVING
PRODUCT
33.
Place the Freezing Cylinder OFF/ON switch in
the ON position.
34.
Press the PUSH TO FREEZE button.
35.
When the product is at 75% consistency, the
display will read “SERVE”.
36.
For normal dispensing, move the spigot handle
fully open.
37.
The machine dispenses product at a reasonable
draw rate. If the machine is overdrawn, the result
is a soft product or a product that will not dispense
at all. If this occurs, allow the machine to run for
approximately 30 seconds before dispensing
more product.
38.
Do not operate the machine when the MIX LOW
message is displayed. Refi ll the mix container
immediately.
NOTE
The machine has a standby and sleep mode. After
a preset number of freezing cycles, it will enter the
standby mode (followed by sleep mode) and remain
there until someone draws product or presses the
PUSH TO FREEZE button. In the sleep mode, the
machine will keep the product below 41°F (7.2°C).
Sleep modes do not take the place of cleaning
and sanitizing. Federal, State, and local regulatory
agencies determine frequency of cleaning and
sanitizing.
3.10 NORMAL FREEZE DOWN AND
OPERATION
The following section contains the recommended oper-
ating procedures for the safe operation of the machine.
A.
Sanitize immediately before use.
B.
Make sure the Freezing Cylinder Off/On switch
is in the OFF position.
C.
Fill the storage containers in the cab with at least
2.5 gallons of mix.
D.
Attach the mix inlet probes to the container and
place the containers in the refrigerated cab.
E.
Place the mix pump switch in the ON position.
F.
Place a container under the spigot and open the
spigot to allow the mix to fl ush out about 8 ounces
(0.23 liters) of sanitizing solution and liquid mix.
Close the spigot.
G.
Open the air bleed valve on the front door by
pressing and holding. Hold the valve open until
the mix level in the freezing cylinder is 1/2” from
the air bleed valve.
H.
Place the Freezing Cylinder OFF/ON switch in
the ON position. Make sure the blender power
plug is connected to the machine and place the
Blender Power Off/On switch in the ON position.
WARNING
Hazardous Moving Parts
Blender shaft and agitator can grab and cause
injury. Do not operate blender without protective
shield or swing splash shield.
I.
Press the PUSH TO FREEZE button.
NOTE
After the drive motor starts, there is a 3-second
delay before the compressor starts.
J.
When the product is at 75% consistency, the
display will read “SERVE”.
K.
For normal dispensing, move the spigot handle
fully open (Fig. 3-9).
L.
On SU412 model, push the spigot handle to the
right to activate the blender. The blender will
operate during or after dispensing product.
M.
Do not operate the machine when the MIX LOW
message is displayed. Refi ll the mix container
immediately.
NOTE
The machine has a standby and sleep mode. After
a preset number of freezing cycles, it will enter the
standby mode (followed by sleep mode) and remain
there until someone draws product or presses the
PUSH TO FREEZE button. In the sleep mode, the
machine will keep the product below 45°F (7.2°C).
Sleep modes do not take the place of cleaning
and sanitizing. Federal, State, and local regulatory
agencies determine frequency of cleaning and
sanitizing.
Figure 3-9 Dispensing Product
Содержание SU412
Страница 1: ...Model SU412 OPERATORS MANUAL Manual No 513625 Rev 4...
Страница 2: ......
Страница 30: ...Owner s Manual 513625 26 SU412 Model Machines...
Страница 36: ...Owner s Manual 513625 32 SU412 Model Machines...
