background image

4

11. Connect the radio speaker/power connecter to the amplifi er body harness and push the connecter up toward 
the air vents to allow radio enough clearance to be reinstalled.  
12. Connect the other end of the amplifi er body harness to the back of the radio and reconnect the other radio 
connection then reinstall radio.
13. Route the power and ground wires of the amplifi er body harness under the carpet and toward the driver’s side 
kick panel.
Route the white two pin connecter of the subwoofer harness under the carpet toward the amp and connect it to the 
white two pin connecter of the amplifi er harness.
14. Connect the power connecters of the subwoofer body harness and the amplifi er body harness to the power 
wires coming through the fi rewall grommet and tuck out of the way.
15. Connect the black ground wires of the subwoofer body harness and the amplifi er body harness to the factory 
ground point near the driver’s side kick panel. Torque to 9 +/- 1.5 Nm. Fig. 6

Amplifi er Installation

16. Remove the three nuts securing the SIR module on the center hump in front of the console. Fig. 7 

Do not 

disconnect the wiring from the module.

17. Lift the module off the studs and set the amplifi er/bracket assembly over the studs.  Reinstall the module over 
the studs and on top of the amplifi er bracket and retighten the nuts. Fig. 8
18. Connect the amplifi er harness to the amplifi er.

Subwoofer Body Harness Routing

19. Remove the lower portion of the rear seat by pulling straight up on the front edge.
20. Snap loose the rear drivers side threshold panel located along the bottom of the door opening. 
21. Snap loose the lower portion of the B pillar post cover.
22. Continue running the subwoofer harness down the drivers side of the car to and under the rear seatback.  It is 
helpful to rotate the seatback down to allow clearance for the connecters.  Secure any excess harness to the 
factory harness under the driver’s side rear threshold panel.

 

Fig. 5 

 

Fig. 6 

Connect ground 
wire(s) to either 

factory ground stud. 

 

Module 

Fig. 7 

 

Amplifier installed over 

module. 

Fig. 8 

Содержание KICKER 19119147









Отзывы: