Still FXH 20 Скачать руководство пользователя страница 92

Страница: 92 / 140

Use

Transporting loads

Transporting a load

Observe the following recommendations:
• Always drive forwards for optimum visibility
• Always travel up or down slopes with the

load uphill Never travel across the slope or

make a U-turn

• Reverse travel is used for depositing

the load As visibility in reverse travel is

restricted, drive at creep speed

• Never drive with an unstable load
• If visibility is poor, let someone guide you
• Be careful of low passageways, low door-

ways, scaffolding, pipes, etc.

• To move past obstacles, slightly raise the

fork arms

• Check that the width of the load is not

greater than the width of the aisle

Setting a load down on the ground

Proceed as follows:
– Drive the machine to the required location.
– Carefully move the load into the unloading

area.

– Lower the load until the fork arms are freed.
– Withdraw the machine in a straight line.
– Raise the fork arms again several centime-

tres.

CAUTION

Risk of falling
Do not touch nearby loads or loads positioned

behind the truck.

CAUTION

Risk of accident
Before you remove the load, ensure that no one is

around the truck or load.

11548011751 EN - 10/2018

Содержание FXH 20













































































































































Результаты поиска

Содержание FXH 20

Отзывы:

Бренды по названию

Популярные бренды

Still FXH 20, Оригинальное руководство пользователя

Результаты поиска

Содержание FXH 20

Отзывы:

Бренды по названию

Популярные бренды