Still FXH 20 Скачать руководство пользователя страница 118

Страница: 118 / 140

Maintenance

Chassis, bodywork and ﬁttings

Cleaning the truck

Cleaning instructions

– Park the truck.
– Press the emergency off switch.

CAUTION

Electrical hazards
The battery must always be disconnected during

cleaning procedures.

Washing the outside of the truck

WARNING

Risk of damage to the truck.
– Do not use ﬂammable liquids to clean the truck.
– The safety rules set out above must be followed

to prevent spark formation. They could lead to a

short circuit.

– All components that are sensitive to moisture

(particularly electric components) must be

protected when the truck is cleaned.

– Follow the manufacturer's instructions when

using the cleaning product.

– Clean the truck with a non-ﬂammable

cleaning product mixed with water, a

sponge and cloths.

– Speciﬁcally clean the oil ﬁller holes and

surrounding area as well as the lubricating

nipples (before lubrication).

NOTE

A frequently cleaned truck must be lubricated

more regularly.

Cleaning the electrical installations

WARNING

Electrical hazards
Do not expose electrical equipment (especially

motors) to direct jets.

NOTE

•

Only use dry cleaning products

•

Do not remove the cowlings

– Clean the electrical installations with

a non-metal brush and dry with lightly

compressed air.

After washing

– Carefully dry the truck (e.g. with com-

pressed air).

WARNING

Use of compressed air
It is advisable to wear protection goggles and a

mask.

– Restart the truck in accordance with the

instructions.

NOTE

If, despite taking precautions, traces of

moisture remain in the motor, dry it using

compressed air. After having eliminated

any traces of moisture, the truck may be

reactivated. Do not do so before then to

prevent any corrosion.

110

11548011751 EN - 10/2018

Содержание FXH 20













































































































































Результаты поиска

Содержание FXH 20

Отзывы:

Бренды по названию

Популярные бренды

Still FXH 20, Оригинальное руководство пользователя

Результаты поиска

Содержание FXH 20

Отзывы:

Бренды по названию

Популярные бренды