Still FXH 20 Скачать руководство пользователя

Страница: 48 / 140

Use

Driver's compartment settings

Adjusting the seat

The driver's seat has several settings, allowing

you to adjust the driving position to suit you:
• The lever (1) allows you to adjust the tilt of

the backrest

• The lever (2) allows you to adjust the

horizontal position

• The adjustment wheel (3) allows you to

adjust the weight of the operator for the

operator presence detector

To adjust the seat, proceed as follows:
– Sit on the seat.
Adjusting the backrest:
– Pull the adjustment lever (1) to tilt the

backrest

Adjusting the depth:
– Pull the adjustment lever (2) to move the

seat forwards or backwards

Weight setting:
The seat is equipped with an operator pres-

ence detector:
The operator must adjust his weight by

increments of 10 kg to trigger this detection.
– Turn the adjustment wheel (3) until the

desired weight is reached

NOTE

The seat's operator presence detector cannot

be activated if the weight setting is too high or

too low.

This operation also enables you to adjust the

hardness of the seat.
– Put the truck into service.

11548011751 EN - 10/2018

Содержание FXH 20













































































































































Результаты поиска

Содержание FXH 20

Отзывы:

Похожие инструкции для FXH 20

Бренды по названию

Популярные бренды

Still FXH 20, Оригинальное руководство пользователя

Результаты поиска

Содержание FXH 20

Отзывы:

Похожие инструкции для FXH 20

Бренды по названию

Популярные бренды