Still FS-X33 Скачать руководство пользователя страница 75

Страница: 75 / 94

Maintenance

Battery maintenance

Maintenance — every 2 years or 4000 h

• Subsequent gearbox oil changes

Battery maintenance

WARNING

Electrolyte (battery acid) is poisonous and corro-

sive on contact. For newly charged batteries in

particular, be aware of the risk of explosion in the

gassing area.
When handling battery acid, the speciﬁed safety

measures must be observed without fail.

The battery is an energy source and must

therefore be handled carefully! - Therefore:
• Keep the battery clean and dry.
• Charge regularly and check the electrolyte

level.

• Check to make sure the cable connections

and battery female connector are in perfect

condition.

• Provide corrosion protection with acid-free

battery grease.

In addition for batteries with liquid electrolyte:
• Check the electrolyte level regularly.
• Overﬂowing electrolyte must be siphoned

off from the battery tray using a siphon.

NOTE

Gel batteries are subject to special char-

ging/maintenance/handling instructions. The

guidelines from the respective manufacturer

must be observed.

To protect the battery from deep discharge, a

discharge indicator with a shutdown function

for the main lift is installed as standard.

CAUTION

If the battery male connector is disconnected while

the consumer is switched on, the contacts can burn.
Only connect and disconnect the battery male

connector when the key switch is turned off.

51328042507 [EN]

Содержание FS-X33































































































Результаты поиска

Содержание FS-X33

Отзывы:

Похожие инструкции для FS-X33

Бренды по названию

Популярные бренды

Still FS-X33, Оригинальное руководство пользователя

Результаты поиска

Содержание FS-X33

Отзывы:

Похожие инструкции для FS-X33

Бренды по названию

Популярные бренды