Still FS-X33 Скачать руководство пользователя страница 55

Страница: 55 / 94

Operation

Travel, Lift, Lower

NOTE

When the direction of travel has been selected

and is indicated on the display, the brake is

released automatically after the accelerator is

touched lightly. This means that the vehicle

moves off immediately.

Select direction of travel Change

direction of travel Reversing

By lightly pressing the switch up (1) or down

(2), you can change over directly from for-

wards to reverse. The braking and the sub-

sequent acceleration in the opposite direction

are controlled electronically.

Operating the lifting equipment

Press operating knob left (1) "Lift" Press

operating knob right (2) "Lower"

Lifting several palettes

This vehicle is designed to accept several

palettes one after another. To avoid pushing

palettes onto the ﬂoor, the palettes to be

accepted should be positioned one in front

of the other so that the forks can pass under

them together.

51328042507 [EN]

Содержание FS-X33































































































Результаты поиска

Содержание FS-X33

Отзывы:

Похожие инструкции для FS-X33

Бренды по названию

Популярные бренды

Still FS-X33, Оригинальное руководство пользователя

Результаты поиска

Содержание FS-X33

Отзывы:

Похожие инструкции для FS-X33

Бренды по названию

Популярные бренды