Still FS-X33 Скачать руководство пользователя страница 35

Страница: 35 / 94

Overview

Safety equipment

NOTE

There is no foot switch in trucks with a driver’s

compartment door or a closed cab.

The hydraulic functions are only enabled if:
• The seat switch and the foot switch have

been actuated.

• The desired hydraulic function is then

selected.

• The switches are all functioning correctly.
The driving function is only enabled if:
• The seat switch and the foot switch have

been actuated but the accelerator pedal

has NOT.

• The accelerator pedal is then actuated.
• The switches are all functioning correctly.
• The parking brake has been released.

NOTE

The parking brake is released as soon as the

accelerator pedal is actuated slightly.

Trucks with two accelerators pedals (dual-

pedal control)
The hydraulic functions are only enabled if:
• The seat switch has been actuated.
• The switch is functioning correctly.
The driving function is only enabled if:
• The seat switch has been actuated but the

accelerator pedals have NOT.

• One of the accelerator pedals is then

actuated.

• The switches are all functioning correctly.
• The parking brake has been released.

NOTE

The parking brake is released as soon as one

of the accelerator pedals is actuated slightly.

Monitoring

The seat switch is monitored electrically. If the

truck remains switched on for longer than 8

hours, the switch status of the seat switch must

51328042507 [EN]

Содержание FS-X33































































































Результаты поиска

Содержание FS-X33

Отзывы:

Похожие инструкции для FS-X33

Бренды по названию

Популярные бренды

Still FS-X33, Оригинальное руководство пользователя

Результаты поиска

Содержание FS-X33

Отзывы:

Похожие инструкции для FS-X33

Бренды по названию

Популярные бренды