Still FS-X33 Скачать руководство пользователя страница 74

Страница: 74 / 94

Maintenance

Maintenance schedule

• Check all hydraulic screw joints for leak

tightness and tighten or exchange as

necessary.

• Check the pump motor operating noise.
• Blow out brush abrasion in the pump motor.

Caution: abrasion is hazardous to your

health, use a protective mask.

• Check the oil level in the tank and top up if

necessary.

Lubrication plan
• Lubrication in accordance with the lubrica-

tion plan.

Operating and protective equipment
• Check or repair protective devices accord-

ing to the equipment.

• Check all operating equipment for function

and condition.

• Check the condition of the driver’s seat.

Also check the adjustability, suspension

and mounting.

Signs
• Check all nameplates, decal information

and warning signs or load capacity dia-

grams to make sure they are present and

legible. Missing or illegible information must

be changed.

Cleaning
• Clean truck with a cloth, compressed air or

vacuum cleaner. Do not use high-pressure

cleaners or solvent!

Maintenance — annual or every 2000 h

• Regular safety inspection must be carried

out by an expert.

NOTE

The corresponding national guidelines must

be observed.

• Change the oil in the hydraulic system
• Lubricate according to lubrication plan

51328042507 [EN]

Содержание FS-X33































































































Результаты поиска

Содержание FS-X33

Отзывы:

Похожие инструкции для FS-X33

Бренды по названию

Популярные бренды

Still FS-X33, Оригинальное руководство пользователя

Результаты поиска

Содержание FS-X33

Отзывы:

Похожие инструкции для FS-X33

Бренды по названию

Популярные бренды